Whirlpool ADVANTECH CAE2761K Скачать руководство пользователя страница 112

Страница: 112 / 178

4-54

To remove a roller:

a) Pry the sides of the triangular ring out

of the groove in the roller support with
a small screwdriver.

Roller Support

Triangular Ring (Shown Partially Removed)

b) Slide the roller off the roller support.

NOTE:

There are two rollers on the front panel

and two on the rear panel, as shown below.

Front Rollers

Rear Rollers

Rear Panel (inside)

Front Panel (inside)

DRUM INSTALLATION NOTE:

Be sure to

position the drum with the clip toward the front
when you reinstall it.

Front

Install Drum

Position Clip

Toward Front

REASSEMBLY NOTE:

Use the following illus-

tration as a guide when installing a new belt.

Idler Pulley

Drum

Drive Motor Pulley

Содержание ADVANTECH CAE2761K



















































































































































































Результаты поиска

Содержание ADVANTECH CAE2761K

Отзывы:

Похожие инструкции для ADVANTECH CAE2761K

Бренды по названию

Популярные бренды

Whirlpool ADVANTECH CAE2761K, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание ADVANTECH CAE2761K

Отзывы:

Похожие инструкции для ADVANTECH CAE2761K

Бренды по названию

Популярные бренды