Whirlpool ADVANTECH CAE2761K Скачать руководство пользователя страница 122

Страница: 122 / 178

5-8

HIGH-LIMIT THERMOSTAT

Refer to pages 4-49 or 4-50 for the procedure
for servicing the high-limit thermostat.

The purpose of the high-limit thermostat is to
cycle off the heat if the heater box area be-
comes higher than 146

C (295

F).

1. Unplug dryer or disconnect power.

2. Turn off gas supply to dryer.

3. Disconnect the wire connectors from the

high-limit thermostat terminals.

4. Set the ohmmeter to the R X 1 scale.

5. Touch the ohmmeter test leads to the high-

limit thermostat terminals. The meter
should indicate a closed circuit (0

Ω

High-Limit

Thermostat

Terminals

FLAME SENSOR

Refer to page 4-50 for the procedure for ser-
vicing the flame sensor.

1. Unplug dryer or disconnect power.

2. Turn off gas supply to dryer.

3. Disconnect the wire connectors from the

flame sensor terminals.

4. Set the ohmmeter to the R X 1 scale.

5. Touch the ohmmeter test leads to the flame

sensor terminals. The meter should indi-
cate a closed circuit (0

Ω

) when cold.

Flame Sensor

Terminals

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

Содержание ADVANTECH CAE2761K



















































































































































































Результаты поиска

Содержание ADVANTECH CAE2761K

Отзывы:

Похожие инструкции для ADVANTECH CAE2761K

Бренды по названию

Популярные бренды

Whirlpool ADVANTECH CAE2761K, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание ADVANTECH CAE2761K

Отзывы:

Похожие инструкции для ADVANTECH CAE2761K

Бренды по названию

Популярные бренды