Whirlpool ADVANTECH CAE2761K Скачать руководство пользователя страница 71

Страница: 71 / 178

4-13

REMOVING THE AGITATOR & TRANSMISSION

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before
operating.

Failure to do so can result in death or
electrical shock.

WARNING

Unplug washer or disconnect power.

To remove the agitator:

a) Unsnap the agitator cap from the agi-

tator and remove it.

To remove the transmission:

a) Tape the washer lid closed.
b) Tilt the washer back at a 45

angle, or

lay it on its back panel.

c) Unclip the two spring clips from the

pump and remove the pump from the
motor shaft (see step 4 on page 4-11).

d) Disconnect the motor wire connector

and the two motor start capacitor wires
(see step 6 on page 4-12).

e) Disconnect the harness clip from the

transmission.

Air Dome Cover

b) Pull off the air dome cover and remove

the rubber O-ring from inside the agita-
tor.

Pump

Transmission

Harness Clip

Spring Clip

(1 of 2)

Agitator Cap

c) Remove the bolt from the agitator and

lift the agitator out of the washer.

Continued on the next page.

Содержание ADVANTECH CAE2761K



















































































































































































Результаты поиска

Содержание ADVANTECH CAE2761K

Отзывы:

Похожие инструкции для ADVANTECH CAE2761K

Бренды по названию

Популярные бренды

Whirlpool ADVANTECH CAE2761K, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание ADVANTECH CAE2761K

Отзывы:

Похожие инструкции для ADVANTECH CAE2761K

Бренды по названию

Популярные бренды