manualshive.com logo in svg

Whirlpool ADVANTECH CAE2761K, Инструкция по установке, эксплуатации и обслуживанию

Подробное руководство по установке, эксплуатации и обслуживанию для продукта Whirlpool ADVANTECH CAE2761K доступно для загрузки совершенно бесплатно на нашем сайте. Этот мануал содержит все необходимые инструкции для правильной работы устройства. Необходимо скачать его с manualshive.com прямо сейчас!

Поделиться
Скачать
background image

- iv -

COMPONENT TESTING

...................................................................................................................... 5-1

Diagnostic Guide ............................................................................................................................. 5-1

WASHERS ............................................................................................................................................

5-2

Motor ............................................................................................................................................... 5-2
Motor Thermal Protector ................................................................................................................. 5-3
Motor Start Capacitor ...................................................................................................................... 5-3
Hidden Lid Switch ........................................................................................................................... 5-4
Dual Water Valve ............................................................................................................................ 5-4
Water Level Switch ......................................................................................................................... 5-5
Basket Drive Shaft Checks ............................................................................................................. 5-6

GAS & ELECTRIC DRYERS ................................................................................................................

5-7

Gas Burner Coils ............................................................................................................................. 5-7
Burner Ignitor .................................................................................................................................. 5-7
Flame Sensor .................................................................................................................................. 5-8
High-Limit Thermostat ..................................................................................................................... 5-8
Heater (Electric Models Only) ......................................................................................................... 5-9
Drive Motor .................................................................................................................................... 5-10
Thermal Fuse ................................................................................................................................ 5-11
Operating Thermostat ................................................................................................................... 5-12
Thermal Cutoff .............................................................................................................................. 5-13
Door Switch ................................................................................................................................... 5-14

DIAGNOSIS & TROUBLESHOOTING

................................................................................................ 6-1

Diagnosis ........................................................................................................................................ 6-1
   Washers With Metercase ............................................................................................................. 6-1
   Freestanding Dryers Without Metercase ..................................................................................... 6-8
   Stack Dryers ............................................................................................................................... 6-13

WIRING DIAGRAMS & STRIP CIRCUITS

........................................................................................... 7-1

Wiring Diagrams .............................................................................................................................. 7-1
   Washers ....................................................................................................................................... 7-1
   Freestanding Electric Dryers ........................................................................................................ 7-2
   Freestanding Gas Dryers ............................................................................................................. 7-3
   Stack Electric Dryers .................................................................................................................... 7-4
   Stack Gas Dryers ......................................................................................................................... 7-5
Dryer Strip Circuits .......................................................................................................................... 7-6

CONTROL BOARD DIAGNOSTICS

..................................................................................................... 8-1

      

ADVANTECH WASHER PARTS

...........................................................................................................9-1

      SERVICE POINTERS

....................................................................................................... Back Of Manu

al

      

WHIRLPOOL COMMERCIAL LAUNDRY CONTACT INFO

........................................Inside Back Cover

Содержание ADVANTECH CAE2761K



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ADVANTECH CAE2761K

Dacor RDW24 Use And Care Manual preview
RDW24
Бренд: Dacor Страницы: 24
Dacor Epicure ED30 Planning Manual preview
Epicure ED30
Бренд: Dacor Страницы: 2
Dacor EDWH24S Planning Manual preview
EDWH24S
Бренд: Dacor Страницы: 3
Dacor EDWH24S Use And Care Manual preview
EDWH24S
Бренд: Dacor Страницы: 24
Dacor EDW24S Use And Care Manual preview
EDW24S
Бренд: Dacor Страницы: 28
Landa PHW Operator'S Manual preview
PHW
Бренд: Landa Страницы: 26
Samsung DW7933LRASR/AA User Manual preview
DW7933LRASR/AA
Бренд: Samsung Страницы: 96
Panasonic NA-F135X1 Service Manual preview
NA-F135X1
Бренд: Panasonic Страницы: 27
Samsung WA45H7200A User Manual preview
WA45H7200A
Бренд: Samsung Страницы: 132
Baumatic BDW71S Instruction Manual preview
BDW71S
Бренд: Baumatic Страницы: 28
Hoonved APS 43 Instructions For User preview
APS 43
Бренд: Hoonved Страницы: 18
Manta WH265 Instruction Manual preview
WH265
Бренд: Manta Страницы: 19
Monogram ZBD68XXK Owner'S Manual preview
ZBD68XXK
Бренд: Monogram Страницы: 2
Kärcher HD 10/15 F Manual preview
HD 10/15 F
Бренд: Kärcher Страницы: 12
F.F. Group PWH 130 PRO Original Instructions Manual preview
PWH 130 PRO
Бренд: F.F. Group Страницы: 56
Ariston AR6L 105 HK Instruction & Installation Manual preview
AR6L 105 HK
Бренд: Ariston Страницы: 16
Speed Queen SCN020G2 Product Specifications preview
SCN020G2
Бренд: Speed Queen Страницы: 1
Hoover DXC 27/1-AUS Manual preview
DXC 27/1-AUS
Бренд: Hoover Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды