manualshive.com logo in svg

Whirlpool ADVANTECH CAE2761K, Инструкция по установке, эксплуатации и обслуживанию

Подробное руководство по установке, эксплуатации и обслуживанию для продукта Whirlpool ADVANTECH CAE2761K доступно для загрузки совершенно бесплатно на нашем сайте. Этот мануал содержит все необходимые инструкции для правильной работы устройства. Необходимо скачать его с manualshive.com прямо сейчас!

Поделиться
Скачать
background image

- iii -

TABLE OF CONTENTS

GENERAL

............................................................................................................................................. 1-1

Safety First ...................................................................................................................................... 1-1
Model & Serial Number Designations ............................................................................................. 1-2
Model & Serial Number Label And Literature Pack Locations ........................................................ 1-3
Specifications .................................................................................................................................. 1-4
   Washers ....................................................................................................................................... 1-4
   Freestanding Dryers .................................................................................................................... 1-5
   Stack Dryers ................................................................................................................................. 1-6
ADVANTECH

 

Money Acceptor Cross Reference

.......................................................................... 1-7

ADVANTECH

  

Money Acceptor Manufacturer Contact Info

 

/

 

Warranty Info

..................................... 1-8

Literature Cross-Reference Chart ................................................................................................... 1-9

INSTALLATION INFORMATION

......................................................................................................... 2-1

Washers .......................................................................................................................................... 2-1
Dryers .............................................................................................................................................. 2-8
Money Acceptor Installation .......................................................................................................... 2-25

PRODUCT OPERATION

...................................................................................................................... 3-1

ADVANTECH

 System Overview ................................................................................................... 3-1

ADVANTECH

 PC System & Palm

 Requirements ....................................................................... 3-2

COMPONENT ACCESS

....................................................................................................................... 4-1

WASHERS ............................................................................................................................................

4-1

Washer Component Locations ........................................................................................................ 4-1
Removing The Console Components ............................................................................................. 4-2
Removing The Money Acceptors & Metercase .............................................................................. 4-6
Removing The Hidden Lid Switch ................................................................................................. 4-10
Removing The Pump, Motor Start Capacitor, & Motor ................................................................. 4-11
Removing The Agitator & Transmission ....................................................................................... 4-13
Removing The Cabinet Assembly ................................................................................................. 4-16
Removing The Tub Ring, Basket, Outer Tub, And Basket Drive Assembly ................................. 4-18
Removing The Suspension System & Base Assembly ................................................................ 4-21
Removing The Vacuum Break ...................................................................................................... 4-22
Removing The Dual Water Valve, Water Level Switch, And Drain Hose Assembly .................... 4-23

DRYERS .............................................................................................................................................

4-25

Gas Dryer Component Locations .................................................................................................. 4-25
Electric Dryer Component Locations ............................................................................................ 4-25

Freestanding Dryers ...........................................................................................................................

4-26

Removing The Console Components ........................................................................................... 4-26
Removing The Money Acceptors & Metercase ............................................................................ 4-29
Removing The Cabinet ................................................................................................................. 4-33

Stack Dryers .......................................................................................................................................

4-35

Removing The Console Components ........................................................................................... 4-35
Removing The Money Acceptors .................................................................................................. 4-38
Removing The ADVANTECH

 Control Boards ............................................................................. 4-40

Removing The Upper Dryer .......................................................................................................... 4-41
Removing The Collar Assembly .................................................................................................... 4-43

Freestanding And Stack Dryers ..........................................................................................................

4-44

Removing The Door Switch .......................................................................................................... 4-44
Removing The Thermal Fuse, Operating Thermostst, Drive Motor, & Broken Belt Switch .......... 4-45
Removing The Heater, The High-Limit Thermostat, & Thermal Cutoff ......................................... 4-49
Removing The Burner Assembly, Flame Sensor, And High-Limit Thermostat ............................. 4-50
Removing The Belt, Drum, & Rollers ............................................................................................ 4-53
Removing The Outlet Grille ........................................................................................................... 4-55
Removing A Spark Quencher ....................................................................................................... 4-56

Page

Содержание ADVANTECH CAE2761K



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ADVANTECH CAE2761K

Zanussi Z 100 Use And Care Instructions Manual preview
Z 100
Бренд: Zanussi Страницы: 28
Campbell Hausfeld PW1550 Operating Instructions And Parts List Manual preview
PW1550
Бренд: Campbell Hausfeld Страницы: 18
Maytag MHW3000BG2 Use & Care Manual preview
MHW3000BG2
Бренд: Maytag Страницы: 48
Rac RAC-HP125 Manual preview
RAC-HP125
Бренд: Rac Страницы: 12
Kärcher HD 6/12-4 C Manual preview
HD 6/12-4 C
Бренд: Kärcher Страницы: 366
GEAppliances WCSE6270 Owner'S Manual preview
WCSE6270
Бренд: GEAppliances Страницы: 16
Kärcher HDS4.0/22 Dealer'S Manual preview
HDS4.0/22
Бренд: Kärcher Страницы: 98
Hotpoint Ariston RSF 723 Instructions For Use Manual preview
RSF 723
Бренд: Hotpoint Ariston Страницы: 48
Hotpoint WMD 740 A Instructions For Use Manual preview
WMD 740 A
Бренд: Hotpoint Страницы: 16
Indesit WITL 126 Instructions For Use Manual preview
WITL 126
Бренд: Indesit Страницы: 24
Hoover Auto-Washer 1100 AC170 User Manual preview
Auto-Washer 1100 AC170
Бренд: Hoover Страницы: 10
GENMAX GPW2500V-E Owner'S Manual And Operating Instructions preview
GPW2500V-E
Бренд: GENMAX Страницы: 36
Walter AGW-180E Operating Manual preview
AGW-180E
Бренд: Walter Страницы: 136
Kärcher HD 3.0/20-4 M Ea Operating Manual preview
HD 3.0/20-4 M Ea
Бренд: Kärcher Страницы: 44
Graco 2730B Instructions Manual preview
2730B
Бренд: Graco Страницы: 32
Zanussi Electrolux ZWF1211W Instruction Booklet preview
ZWF1211W
Бренд: Zanussi Electrolux Страницы: 28
Dexter Laundry T-1200 WC1200XA-12 Schematics preview
T-1200 WC1200XA-12
Бренд: Dexter Laundry Страницы: 25
Heinner HDW-BI4506A++ Manual preview
HDW-BI4506A++
Бренд: Heinner Страницы: 50

Бренды по названию

Популярные бренды

Загрузить еще бренды