Graco 2730B Скачать руководство пользователя страница 1

Страница: 1 / 32

309286

Rev. B

First choice when

quality counts.

INSTRUCTIONS

This manual contains important
warnings and information.
READ AND KEEP FOR REFERENCE.

Direct-Drive Pressure Washers

2730B

Model 244389, Series A with Briggs & Stratton 6.5 HP Motor

2700 psi (186 bar, 18.6 MPa) Operating Pressure
3000 psi (206 bar, 20.6 MPa) Maximum Working Pressure

2730H

Model 244390, Series A with Honda 6.5 HP Motor

2700 psi (186 bar, 18.6 MPa) Operating Pressure
3000 psi (206 bar, 20.6 MPa) Maximum Working Pressure

3030

Model 244391, Series A

3000 psi (206 bar, 20.6 MPa) Operating Pressure
3300 psi (227.5 bar, 22.75 MPa) Maximum Working Pressure

3340

Model 244392, Series A

3300 psi (227.5 bar, 22.75 MPa) Operating Pressure
3600 psi (248 bar, 24.8 MPa) Maximum Working Pressure

3540

Model 244393, Series A

3500 psi (241 bar, 24.1 MPa) Operating Pressure
3800 psi (262 bar, 26.2 MPa) Maximum Working Pressure

GRACO INC.

P.O. BOX 1441

MINNEAPOLIS, MN

55440–1441

Graco Inc. is registered to I.S. EN ISO 9001

3340 Pressure Washer
Model 244392 Shown

7329B

Содержание 2730B

































Результаты поиска

Содержание 2730B

Отзывы:

Похожие инструкции для 2730B

Бренды по названию

Популярные бренды

Graco 2730B, Инструкция по эксплуатации

Результаты поиска

Содержание 2730B

Отзывы:

Похожие инструкции для 2730B

Бренды по названию

Популярные бренды