Whirlpool ADVANTECH CAE2761K Скачать руководство пользователя страница 85

Страница: 85 / 178

4-27

To remove the membrane switch:

a) From the rear of the unit, remove the

screw from either of the end caps.

End Cap

Rear Screw

b) Remove the ADVANTECH



control and

display boards (see steps 5 and 6).

c) Remove the two ground screws from

the green ground wires.

NOTE:

The membrane switch board will be

loose when you remove the bracket screws in
the next step. Be careful not to drop the board
when you remove the bracket.

d) Remove the two end cap screws from

both ends of the console bracket. Care-
fully lift the bracket from the console,
and remove the loose end cap and the
membrane switch board.

e) Bend the tabs on the membrane switch

and remove them from the slots in the
board.

NOTE:

Be sure to install the new

membrane switch on the board with the
ribbon cable facing the end with the two
alignment pins that are on the opposite
side of the board. Also make sure that
the ends of the two alignment pins are
in their bracket holes.

Ground Screws

End Cap Screws

Hinge

Alignment Pin

Ribbon Cable

Membrane Switch

Membrane Switch Tabs

Continued on the next page.

Backer Board

Содержание ADVANTECH CAE2761K



















































































































































































Результаты поиска

Содержание ADVANTECH CAE2761K

Отзывы:

Похожие инструкции для ADVANTECH CAE2761K

Бренды по названию

Популярные бренды

Whirlpool ADVANTECH CAE2761K, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание ADVANTECH CAE2761K

Отзывы:

Похожие инструкции для ADVANTECH CAE2761K

Бренды по названию

Популярные бренды