Whirlpool ADVANTECH CAE2761K Скачать руководство пользователя страница 65

Страница: 65 / 178

4-7

To remove the card reader assembly:

a) Using a 5/16

″

socket, unscrew the

retaining bolt from the money accep-
tor, and remove the bolt from inside the
metercase.

b) Lift and pull the card reader assembly

forward and remove it from the
metercase.

c) Position the console to its service po-

sition (see page 4-2 for the procedure).

d) If you are changing to a different type

of money acceptor, disconnect the con-
nector from P11 on the ADVANTECH



control board, and remove the card
reader wire harness.

c) Lift the coinslide to release it from the

holes in the metercase, and pull it
forward out of the metercase.

d) Unplug the two wires from the coinslide

switch.

Coinslide Switch
With 2 Wires

5/16

″

Retaining Bolt

P11

ADVANTECH



Control Board

e) If you are replacing a defective card

reader, disconnect the wire connector
from the card reader assembly.

Continued on the next page.

Card

Reader

Assembly

Содержание ADVANTECH CAE2761K



















































































































































































Результаты поиска

Содержание ADVANTECH CAE2761K

Отзывы:

Похожие инструкции для ADVANTECH CAE2761K

Бренды по названию

Популярные бренды

Whirlpool ADVANTECH CAE2761K, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание ADVANTECH CAE2761K

Отзывы:

Похожие инструкции для ADVANTECH CAE2761K

Бренды по названию

Популярные бренды