Whirlpool ADVANTECH CAE2761K Скачать руководство пользователя страница 162 | Manualshive

Страница: 162 / 178

background image

THIS SERVICE POINTER APPLIES TO THE FOLLOWING BRANDS:

REFRIGERATION PRODUCTS

KITCHEN PRODUCTS

LAUNDRY PRODUCTS

COMMERICAL LAUNDRY

OEM BRANDS

ALL SERVICE POINTERS ONLINE: http://www.whirlpoolcorp.com/servicematters/tech_ref/tech_ref_main.htm, SERVICE POINTERS

COMMERCIAL LAUNDRY ONLY: www.whirlpoolcorp.com/cltpsc, TECHNICAL INFORMATION, SERVICE POINTERS

To receive pointers by email or FAX, or to edit or delete a current email or Fax from our distribution, see

http://www.whirlpoolcorp.com/cltpsc/feedback/feedbacksubscribe_all.html,

or FAX changes to 269-923-5342.

ALL FREEST

ALL FREEST

ALL FREEST

ALL FREEST

ALL FREESTANDING METERCASE

ANDING METERCASE

ANDING METERCASE

ANDING METERCASE

ANDING METERCASE

EQUIPPED AD

EQUIPPED AD

EQUIPPED AD

EQUIPPED AD

EQUIPPED ADV

V

V

V

VANTECH™ W

ANTECH™ W

ANTECH™ W

ANTECH™ W

ANTECH™ WASHERS

ASHERS

ASHERS

ASHERS

ASHERS

AND DRYERS

AND DRYERS

AND DRYERS

AND DRYERS

AND DRYERS

!

!

!

!

!

!

!

!

!

!

THE DRYER DISPLAY SHOWS 240 MINUTES;

CUSTOMERS DO NOT HAVE TO PAY TO OPERATE DRYER.

ELECTRIC DRYER MODELS

GAS DRYER MODELS

CEE2760KQ0

CGE2761KQ0

CEE2790KQ0

CGE2791KQ0

The dryer display shows 240 minutes.

Customers do not

have to pay to operate the dryer.

COMPLAINT:

CAUSE:

A software issue causes the dryer to count up to

240

minutes ONLY when a coindrop is installed and the cus-
tomer selects a cycle between 12:00 and 1:00PM on
Monday. After operation on Several Mondays between
12:00 and 1:00PM, 240 minutes will be displayed.

RESOLUTION:

The firmware version on the dryer board must be updat-
ed from version 3.12 to version 3.13 by downloading a
firmware update from the Trade Partner Support Center
site at www.whirlpoolcrop.com/cltpsc, or by replacing the
control board, part number 3407165.

All ADVANTECH™ Commercial Laundry controls are re-
programmable through the infrared communications port

(continued)

L8178296

L8178296

L8178296

L8178296

L8178296

February 2003

February 2003

February 2003

February 2003

February 2003

with a Palm™ OS equipped handheld loaded with the
ADVANTECH™ software application.

When additional features are added to the ADVANTECH™
firmware, they can be downloaded from the link below by
selecting the download FRMW for washers and download
FRMD for dryers. Download to the following directory:
C:\Palm\add-on. The firmware can then be imported to
the ADVANTECH™ Software application, transferred to
the Palm™ OS equipped handheld, then beamed via
infrared into the washer or dryer control.

NOTE:

In order to update the firmware, ADVANTECH™

management software program must be installed and op-
erational on your PC.

NOTE:

Before proceeding all passwords including ser-

vice tech ID must be set and loaded onto the handheld. If
collecting audit data, collect prior to reprogramming, as
new firmware will delete all service, set up and audit data.

«
...
160
161
162
163
164
...
»

Содержание ADVANTECH CAE2761K



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ADVANTECH CAE2761K

Бренд: bar aid Страницы: 16

Бренд: GE Страницы: 11

Бренд: Haier Страницы: 6

Бренд: Haier Страницы: 6

Бренд: Haier Страницы: 24

Бренд: Haier Страницы: 12

Бренд: Haier Страницы: 12

Бренд: Haier Страницы: 23

Бренд: Haier Страницы: 12

Бренд: GE Страницы: 26

Бренд: CALOR Страницы: 20

Бренд: Washtech Страницы: 12

Бренд: Crosley Страницы: 60

Бренд: Majestic Appliances Страницы: 29

Бренд: Kärcher Страницы: 16

Бренд: Philco Страницы: 51

Бренд: RAMTONS Страницы: 7

Бренд: Indesit Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды