Whirlpool ADVANTECH CAE2761K Скачать руководство пользователя страница 67

Страница: 67 / 178

4-9

To remove the metercase:

a) Remove the money acceptor from the

metercase.

c) Unsnap the locking arms from the bot-

tom of the coin funnel and remove the
funnel from the metercase.

d) Remove the 1/2

″

hex-head screws from

the front and rear of the metercase,
then lift the metercase off the washer,
and remove it.

1/2

″

Hex-Head Front

Metercase Screws

To remove the service switch:

a) Push up on the switch body, and re-

move the switch from the retaining
bracket from inside the metercase.

b) Disconnect the two wires from the ser-

vice switch terminals.

Service Switch Wires

Retaining Bracket

Coin Funnel

b) Unlock and remove the coinbox.

Money

Acceptor

To remove the adapter plate:

a) Remove the coinbox.
b) Unlock and remove the service access

door.

c) Using a ratchet with a 10

″

extension

and a 3/8

″

socket, remove the two hex-

nuts from the adapter plate through the
service access opening.

d) Remove the 3/8

″

hex-nut from the top

of the coinbox opening. Pull from the
top, and remove the adapter plate.

Hex-Nuts (Behind

Adapter Plate)

Adapter Plate

Hex-Nut

Coinbox Area

Содержание ADVANTECH CAE2761K



















































































































































































Результаты поиска

Содержание ADVANTECH CAE2761K

Отзывы:

Похожие инструкции для ADVANTECH CAE2761K

Бренды по названию

Популярные бренды

Whirlpool ADVANTECH CAE2761K, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание ADVANTECH CAE2761K

Отзывы:

Похожие инструкции для ADVANTECH CAE2761K

Бренды по названию

Популярные бренды