Intel 81341 Скачать руководство пользователя страница 408 | Manualshive

Страница: 408 / 1056

background image

Intel

®

81341 and 81342—Messaging Unit

Intel

®

81341 and 81342 I/O Processors

Developer’s Manual

December 2007

408

Order Number: 315037-002US

4.3

Message Registers

Messages can be sent and received by the 81341 and 81342 through the use of the

Message Registers. When written, the message registers may cause an interrupt to be

generated to either the Intel XScale

®

processor or the host processor. Inbound

messages are sent by the host processor and received by the 81341 and 81342.

Outbound messages are sent by the 81341 and 81342 and received by the host

processor.
The interrupt status for outbound messages is recorded in the Outbound Interrupt

Status Register. Interrupt status for inbound messages is recorded in the Inbound

Interrupt Status Register.

4.3.1

Outbound Messages

When an outbound message register is written by the Intel XScale

®

processor, an

interrupt may be generated on the

P_INTA#

interrupt pins or a message signaled

interrupt is generated when MSI is enabled.
The PCI interrupt is recorded in the Outbound Interrupt Status Register. The interrupt

causes the Outbound Message Interrupt bit to be set in the Outbound Interrupt Status

Register. This is a Read/Clear bit that is set by the MU hardware and cleared by

software.
The interrupt is cleared when an external PCI agent writes a value of 1 to the Outbound

Message Interrupt bit in the Outbound Interrupt Status Register to clear the bit.
The interrupt may be masked by the mask bits in the Outbound Interrupt Mask

Register.

4.3.2

Inbound Messages

When an inbound message register is written by an external PCI agent, an interrupt

may be generated to the Intel XScale

®

processor. The interrupt may be masked by the

mask bits in the Inbound Interrupt Mask Register.
The Intel XScale

®

processor interrupt is recorded in the Inbound Interrupt Status

Register. The interrupt causes the Inbound Message Interrupt bit to be set in the

Inbound Interrupt Status Register. This is a Read/Clear bit that is set by the MU

hardware and cleared by software.
The interrupt is cleared when the Intel XScale

®

processor writes a value of 1 to the

Inbound Message Interrupt bit in the Inbound Interrupt Status Register.

«
...
406
407
408
409
410
...
»

Содержание 81341

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 81341

Бренд: ABB Страницы: 66

Бренд: Maco Страницы: 38

ShareCenter DNS-320L

Бренд: D-Link Страницы: 4

Бренд: Quatech Страницы: 27

Бренд: 3Com Страницы: 16

Бренд: Paradyne Страницы: 45

Бренд: SeaLevel Страницы: 17

Бренд: Grizzly Страницы: 9

PCI-6110E/6111E

Бренд: National Instruments Страницы: 113

Бренд: protech Страницы: 95

Бренд: Crown Страницы: 7

Бренд: National Instruments Страницы: 52

MULTIflight Stick

Бренд: Multiplex Страницы: 10

CloudGen Firewall

Бренд: Barracuda Страницы: 8

Бренд: DTS Страницы: 94

SteelCentral NetExpress 470

Бренд: Riverbed Страницы: 140

Бренд: EVGA Страницы: 3

Бренд: EK-Quantum Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды