Intel 81341 Скачать руководство пользователя страница 251

Страница: 251 / 1056

Intel

81341 and 81342 I/O Processors

December 2007

Developer’s Manual

Order Number: 315037-002US

251

Address Translation Unit (PCI Express)—Intel

81341 and 81342

3.3.2.2

Outbound Address Translation Windows

Inbound translation involves a programmable inbound translation window consisting of

a base and limit register and a value register for PCI to internal bus translation. The

outbound address translation windows use a similar methodology except that the

outbound translation window limit sizes are fixed in 81341 and 81342 internal bus

address space; this removes the need for separate limit registers.

Figure 28 on page 254

illustrates the five outbound address translation windows. The

ATU has four 4 Gbyte outbound memory translation windows and one 64 Kbyte

outbound I/O translation window. By default, Outbound Memory Window 0

(OUMBAR0), Outbound Memory Window 1 (OUMBAR1), Outbound Memory Window 2

(OUMBAR2), and the Outbound Memory Window 3 (OUMBAR3) reside in 4 Gbyte

memory sections 1, 2, 3, and 4, respectively. The default location of the 64 KByte

outbound I/O window range is from 0.FFFD.0000H to 0.FFFD.FFFFH. The following

registers are used to specify the five 4 Gbyte windows for claiming Outbound Memory

transactions:

• Outbound Upper Memory Base Address Register 0 (OUMBAR0)

— Default Value equal to 01H.

• Outbound Upper Memory Base Address Register 1 (OUMBAR1)

— Default Value equal to 02H.

• Outbound Upper Memory Base Address Register 2 (OUMBAR2)

— Default Value equal to 03H.

• Outbound Upper Memory Base Address Register 3 (OUMBAR3)

— Default Value equal to 04H.

• Outbound I/O Base Address Register (OIOBAR)

— Default Value equal to 0FFF D000H

An internal bus cycle with an address within one of the outbound windows initiates a

read or write request on the PCI Express Link. The PCI transaction type depends on

which translation window the local bus cycle “hits”. The read or write decision is based

on the internal bus cycle type.
ATU has windows dedicated to the following outbound transaction types:

• Memory reads and Memory writes - Memory Window

• I/O reads and writes - I/O Window

Table 119. Internal Bus-to-PCI Command Translation for Memory Windows

Internal Bus Command

PCI Express Transaction Type

Write

Memory Write Request

Read

Memory Read Request

Table 120. Internal Bus-to-PCI Command Translation for I/O Window

Internal Bus Command

a. User should designate memory region containing I/O Window as non-cachable and non-bufferable from Intel

XScale

processor. This insures all load/stores to I/O Window are of DWORD quantities. In the event that the

user inadvertently issues a read to the I/O Window which crosses a DWORD address boundary, the ATU target

aborts the transaction. Only bytes 3:0 is relevant dependent on the Byte Enables.

Conventional PCI Command

Write

I/O Write Request

Read

I/O Read Request

Содержание 81341

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 81341

Отзывы:

Похожие инструкции для 81341

Бренды по названию

Популярные бренды

Intel 81341, Руководство разработчика

Результаты поиска

Содержание 81341

Отзывы:

Похожие инструкции для 81341

Бренды по названию

Популярные бренды