Intel 81341 Скачать руководство пользователя страница 294 | Manualshive

Страница: 294 / 1056

background image

Intel

®

81341 and 81342—Address Translation Unit (PCI Express)

Intel

®

81341 and 81342 I/O Processors

Developer’s Manual

December 2007

294

Order Number: 315037-002US

3.16.1

Extended Capabilities Registers

The ATU unit includes 5 extended capability configuration spaces beginning at

configuration offset 90H, 98H, A0H, B0H, and D0H. The extended configuration spaces

can be accessed by a device on the PCI interface through a mechanism defined in the

PCI Express Specification.
In the ATU Status Register (

) the appropriate bit is set indicating that the

Extended Capability Configuration space is supported. When this bit is read, the device

can then read the Capabilities Pointer register (

Section 3.16.23

) to determine the

configuration offset of the Extended Capabilities Configuration Header. The format of

these headers are depicted in

.

The first byte at the Extended Configuration Offset 98H is the ATU Capability Identifier

Register for the PCI Bus Power Management Interface Specification, Revision 1.1.
Following the Capability Identifier Register is the single byte Next Item Pointer Register

(

Section 3.16.51, “PM Next Item Pointer Register - PM_Next_Item_Ptr” on page 341

)

which indicates the configuration offset of an additional Extended Capabilities Header,

when supported. In the ATU, the Next Item Pointer Register is set to D0H indicating

that there is an additional Extended Capabilities Headers supported in the ATUs

configuration space.
To enable the PCI Bus Power Management Interface Specification, Revision 1.1

compliance support, the Power State Transition interrupt mask in bit 8 of the ATUIMR

needs to be cleared. It is the configuration software’s responsibility to properly enable

and initialize the ATUs Power Management Interface before the Configuration Cycle

Retry Bit in the

Section 3.16.41, “PCI Configuration and Status Register - PCSR” on

is cleared in order for the ATU to be Advanced Configuration and Power

Interface Specification, Revision 2.0 compliant.

Note:

MSI-X Capability Registers are defined in

Chapter 4.0, “Messaging Unit.”

The first byte at the Extended Configuration Offset B0H is the MSI-X Capability

Identifier Register (

Section 4.9.36, “MSI-X Capability Identifier Register - MSI-

). This identifies this Extended Configuration Header space as the type

defined by the PCI Local Bus Specification, Revision 2.3.
Following the Capability Identifier Register is the single byte Next Item Pointer Register

(

Section 4.9.37, “MSI-X Next Item Pointer Register - MSI-X_Next_Item_Ptr”

) which

indicates the configuration offset of an additional Extended Capabilities Header, when

supported. In the ATU, the Next Item Pointer Register is set to A0H indicating that

there is an additional Extended Capabilities Headers supported in the ATUs

configuration space.

Figure 35. ATU Interface Extended Configuration Header Format (Power Management)

98H

9CH

Capability Identifier

Next Item Pointer

Power Management Capabilities

Power Management Control/Status

Reserved

Figure 36. ATU Interface Extended Configuration Header Format (MSI-X Capability)

B0H

B4H

MSI-X Capability ID

MSI-X Next Item Pointer

MSI-X Message Control

MSI-X Table Offset

MSI-X PBA Offset

B8H

Table BIR

PBA BIR

«
...
292
293
294
295
296
...
»

Содержание 81341

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 81341

Бренд: Palo Alto Network Страницы: 56

Бренд: Cromemco Страницы: 46

Бренд: Verizon Wireless Страницы: 39

TD-3316B4-16P-A1

Бренд: TVT Digital Страницы: 2

Digital Encoder Plus

Бренд: IDT Страницы: 98

dspstak 21262sx

Бренд: Danville Signal Processing Страницы: 35

EK-FC980 GTX Classy

Бренд: ekwb Страницы: 2

Бренд: MSNswitch Страницы: 2

Open Standard Module RPX30 EVA-MI V1

Бренд: iesy Страницы: 9

Бренд: Quadram Страницы: 21

Бренд: B&B Electronics Страницы: 24

Бренд: RME Audio Страницы: 7

Бренд: C&H Technologies Страницы: 2

Бренд: Eneo Страницы: 49

Бренд: Cypress Semiconductor Страницы: 31

Бренд: Dell Страницы: 37

1000 Con?guration guide

Бренд: Nortel Страницы: 108

Бренд: Dell Страницы: 90

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды