Network Video Recorder
Quick Start Guide
The interfaces of the rear panel are for reference only.
4. Rear Panel Instruction
7.
Network Configuration & Add IP Camera
5
Startup
&
Shutdown
►Startup
①
Connect the monitor and the power.
②
The device will boot and the power indicator will display blue.
③
A wizard window will pop up.
►Shutdown
Click “Start” and then select “Shutdown” icon. This will bring up a shutdown
window. The device will shut down by clicking “OK” button. Then disconnect
the power.
6.
Login
After you finish adding IP cameras, you can see the live images through the
monitor of the NVR. The following will mainly introduce how to add the IP
cameras via LAN/WAN.
►
LAN
①
Set the network of the NVR. Go to Start
→
Settings
→
Network
→
TCP/IP.
Enter IP address, subnet mask, gateway, etc. If using DHCP, please enable DHCP
in both the NVR and the router.
②
Go to Start
→
Settings
→
Network
→
Port. Enter HTTP port (the default
value is 80), server port (the default port is 6036).
③
The
internal ethernet port is the port which connects all the PoE ports with
the NVR system. The PoE ports are available if the internal ethernet port is
online; if it is offline, all the PoE ports will be unavailable. The IP address and
subnet mask of the internal ethernet port can be changed to make the port in the
same network segment with the IP cameras which directly connect to the PoE
ports of the NVR.
④
Go to Start
→
Settings
→
Camera
→
Add Camera. The NVR will automatically
refresh the cameras searched. The IPC which supports the Onvif protocol may
be added manually. If the IPC searched is not in the same local network as the
NVR, you should select the device and click to modify the IP address.
3.4.2
3.4.2
4.0.0.1.beta1
Version
80
80
80
No.
Address
Edit
Port
Protocol
Model
Subnet Mask
1
2
3
192.168.1.20
192.168.1.38
192.168.2.45
XXX
XXX
XXX
XXX
XXX
XXX
255
.
255
.
255
.
0
255
.
255
.
255
.
0
255
.
255
.
255
.
0
Quickly Add
Manually
Add
Add Recorder
Add
Camera
Selected: 1/3
Add
Default Password
Remain
Bandwidth
:
108
/
120
Mb
Cancel
Username
Password
admin
Login
Enter Password
Display Password
Log In Automatically
IP Address Settings
Obtain an IPv4 address automatically
Obtain
DNS
automatically
Obtain an IPv6 address automatically
Internal
Ethernet Port ( Online )
Address
Address
192 . 168 . 1 . 2
.
.
.
255
255
255
255
. . .
. . .
0
192 . 168 . 1 . 1
1500
Subnet Mask
Preferred
DNS
Alternate
DNS
Mask Length
Gateway
Gateway
MTU
Apply
Ethernet Port 1 ( Online )
2
.
Packing Check
Please check the device and the accessories after getting the device. If there
are any damages, shortages or defects, please contact your dealer immediately.
1
.
Notes
●
Please read this instruction carefully before using the product and keep
it for further reference.
●
All the examples and pictures used here are for reference only.
●
The contents of this manual are subject to change without notice.
●
This device should be operated only from the type of power source indicated
on the marking label. The voltage of the power must be verified before using
the same.
The default username is
admin
and the default password is
123456
. You must
configure the wizard if you start the NVR for the first time and you may change
the password when you configure the wizard for the first time. You can skip
the settings of wizard next time. Click “Start” and select “Login”. This will take
you to see a login box. Enter default username and password you set and you can
see the live image.
3
.
HDD
Installation
Audio
input
Audio
output
Connect
to
high
definition
display
device
Connect
to
monitor
Network
port
PoE network
ports; connect to PoE IP camera
Connect to USB storage device or USB mouse
AUDIO
OUT
Name
Description
AUDIO
IN
VGA
PoE Ports
HDMI
LAN
USB
ALARM
OUT
Alarm inutput;
ALARM
IN
Alarm input; connectors for sensors
GND
Ground
P/Z
P/Z; Connector for PTZ
K/B
K/B; Connector for keyboard
Edit ecurity
uestion
S
Q
Login
Cancel
This series of the product supports 4 SATA hard drives. Please make sure that the
device is powered off before the installation. The pictures of the installation are only
for reference.
①
Loosen the screws to open the cover.
②
Screw the screws into the holes of the HDD but not tighten them.
③
Turn over the machine and place
the HDD with two screws onto the bottom
of the case. Then lock the screws according to the order of the marks.
④
Install
the
other
three
HDDs
according
to above
-
mentioned
method
.
⑤
Connect the power and data cables.
Tips:
Please check the inside structure of the device and make sure the cables connected
well before installing the cover back. Please format the HDD before using.
⑥
Install back the cover and secure it with the screws.
