Intel 81341 Скачать руководство пользователя страница 287

Страница: 287 / 1056

Intel

81341 and 81342 I/O Processors

December 2007

Developer’s Manual

Order Number: 315037-002US

287

Address Translation Unit (PCI Express)—Intel

81341 and 81342

3.13.2

Accessing Vital Product Data

The VPD Capabilities List Item provides three fields which the system uses to access

the Vital Product Data:

VPD Address

DWORD Aligned Byte address of the VPD to be accessed which

is represented by VPDAR[14:0]. Note that this means that the

maximum size of the VPD is 128 Kbytes. The user may pick any

128 Kbyte block of memory in the storage component for the

VPD.

Flag

The flag register is used to indicate when the transfer between

the VPD Data Register and the storage component is completed.

The flag is in VPDAR[15] which means that the Flag is written at

the same time that VPD address is written.

VPD Data

Four bytes of VPD Data can be read or written through this field

which is represented by VPDDR[31:0]. The least significant byte

of this register represents the byte at the VPD Address

(VPDAR[14:0]). Four bytes are always transferred between this

3.13.2.1 Reading Vital Product Data

Using the fields defined in the VPD Capabilities List Item, the 81341 and 81342 reads

Vital Product Data using the following sequence of events:

1. Host processor executes a configuration write of the VPD address to the VPDAR

with the Flag cleared.

2. An interrupt to the Intel XScale

processor is triggered and bit 17 of the ATUISR is

set. Meanwhile, the host processor polls the VPDAR register waiting for the Flag to

be set.

Warning:

When any configuration writes to either the VPDAR or the VPDDR occur prior to the Flag

being set, the results of the original read operation are unpredictable.

3. Using the VPD Address, the Intel XScale

processor retrieves the Vital Product

Data from the VPD storage component (i.e., Flash Memory).

4. The Intel XScale

processor then writes this data to VPD Data Register (VPDDR).

5. The Intel XScale

processor clears the VPD interrupt status bit in the ATUISR.

6. The Intel XScale

processor then sets the Flag in the VPDAR register.

7. When the host processor detects that the Flag has been set, the host processor

then reads the retrieved VPD from the VPDDR.

Содержание 81341

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 81341

Отзывы:

Похожие инструкции для 81341

Бренды по названию

Популярные бренды

Intel 81341, Руководство разработчика

Результаты поиска

Содержание 81341

Отзывы:

Похожие инструкции для 81341

Бренды по названию

Популярные бренды