Intel 81341 Скачать руководство пользователя страница 246 | Manualshive

Страница: 246 / 1056

background image

Intel

®

81341 and 81342—Address Translation Unit (PCI Express)

Intel

®

81341 and 81342 I/O Processors

Developer’s Manual

December 2007

246

Order Number: 315037-002US

3.3.1.3

Inbound Memory Read Transaction

An inbound read transaction is initiated by a PCI Express requester and is targeted at

either local memory or a memory-mapped register space. The read transaction is

propagated through the inbound non posted queue (INPQ) and read data is returned

through outbound completion data and header queues (OCPLHQ, OCPLDQ).
In PCI Express, all read transactions are processed as split transactions. The ATUs PCI

Express interface accepts the read transaction and forwards the read request through

to the internal bus and returns the read data to the PCI Express Link. Data flow for an

inbound read transaction is summarized in the following statements:

• The ATU accepts the read transaction when the PCI address is within one of the

inbound translation windows defined by ATU Inbound Base Address Register,

Inbound Upper Base Address Register, and Inbound Limit Register.

• When the transaction crosses a 1KB aligned boundary it is fragmented into smaller

requests that do not cross the aligned boundary before it is issued on the internal

bus. Since PCI Express transactions cannot cross a 4KB boundary, a single read

request is broken into at most 4 1KB transactions.

• When sufficient space exists in OCPLDQ, request internal bus and issue request.

• Save the completion header information in the OCLUT.

• ATUE can handle a maximum of 4 outstanding internal bus requests at one time.

• All internal bus read requests result in split completions. The completion data is

queued in the Outbound Completion Data Queue.

• A zero length read (memory read request of 1 DW with no bytes enabled) has no

side-effects.

• Once a completion transaction has started, it continues until one of the following is

true:

— The length is satisfied.

— An internal bus Master Abort or Target Abort was detected. The ATU generates

a Completion TLP with a Completer Abort status to inform the requester about

the abnormal condition. The INPHQ for this transaction is flushed. Refer to

.

The data flow for an inbound read transaction on the internal bus is summarized in the

following statements:

• The ATU internal bus master interface requests the internal bus when a PCI address

appears in an INPHQ and transaction ordering has been satisfied. The ATU takes

advantage of the information provided by the Relaxed Ordering Attribute bit.

• Once the internal bus is granted, the internal bus master interface drives the

translated address onto the bus. When a Retry is signaled, the request is repeated.

When a master abort occurs, transaction is considered complete and an

unsupported request Completion is loaded into OCPLHQ for return to the PCI

Express requester (request is flushed once the completion has been posted to the

OCPLHQ).

• Once the translated address is on the bus and the transaction has been claimed,

the internal bus target starts returning data using a split response. Read data is

continuously received by the OCPLDQ until one of the following is true:

— The full byte count requested by the ATU read request is received. The internal

bus completer’s initiator interface performs an initiator completion in this case.

— A partial byte count requested by the ATU read request is received. The

completer’s internal bus initiator interface performs an initiator completion in

this case. Also, the completer reacquires the internal bus to deliver the

remaining read data byte count to the ATU.

«
...
244
245
246
247
248
...
»

Содержание 81341

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 81341

Бренд: Acconeer Страницы: 32

DR-4100P Series

Бренд: Idis Страницы: 30

COMSPHERE 3800 Series

Бренд: Paradyne Страницы: 88

COMSPHERE 3800PLUS

Бренд: Paradyne Страницы: 5

S5120V3-EI Series

Бренд: H3C Страницы: 54

Бренд: Ublox Страницы: 116

Бренд: Opengear Страницы: 2

Brocade X6-8 Director

Бренд: Broadcom Страницы: 207

Бренд: Lanner Страницы: 63

CNPS5X PERFORMA

Бренд: ZALMAN Страницы: 8

Бренд: Symantec Страницы: 100

Бренд: PaloAlto Networks Страницы: 28

Бренд: Xilinx Страницы: 29

OPTIMA II CNPS10X

Бренд: ZALMAN Страницы: 20

Бренд: Arctic Страницы: 7

NexXxoS GPX-N 970 M03

Бренд: Alphacool Страницы: 2

Бренд: ADTRAN Страницы: 4

mvHYPERION-32R16

Бренд: Matrix Vision Страницы: 148

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды