Intel 81341 Скачать руководство пользователя страница 686

Страница: 686 / 1056

Intel

81341 and 81342—SRAM Memory Controller

Intel

81341 and 81342 I/O Processors

Developer’s Manual

December 2007

686

Order Number: 315037-002US

8.3.3.3

ECC Checking

The ECC logic uses the following ECC read algorithm. This algorithm corrects the data

before it's driven onto the internal bus. The ECC algorithm for a read transaction is:

Read 32-bit data and 7-bit ECC

Compute the syndrome by passing the 32-bit data through the G-Matrix and XORing the
7-bit result with the 7-bit ECC

if the syndrome <> 0 {ECC Error}

Look up in H-matrix to determine error type

if error is correctable {single bit}

if single-bit error correction is enabled

Correct data

Send corrected data to internal bus

if single bit error reporting is enabled

Interrupt core for software scrubbing

else {uncorrectable}

if the read cycle is

not

part of a RMW cycle {read}

Target-Abort the Internal Bus read transaction.

else {write requiring RMW}

Merge the new data portion with the read data from memory

Generate the new ECC with the G-matrix

Write new data and ECC

if multi-bit error reporting is enabled

Interrupt the core for uncorrectable error

When the SMCU reads the ECC from the memory subsystem, it is compared (XORed)

with an ECC result that the SMCU generates from the data read from the memory. The

resulting value of the XOR operation is called the syndrome.

Table 416

shows how the

SMCU decodes the syndrome for SRAM read cycles.

Table 416. Syndrome Decoding

Error Type

Symptom

None

The syndrome is 0000 0000.

Single-Bit

Use the H-Matrix in

Figure 104

to determine which bit the SMCU will invert to fix the error.

Multi-Bit

If the Syndrome does not match an 7-bit value in the H-matrix, the error is uncorrectable

Содержание 81341

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 81341

Отзывы:

Похожие инструкции для 81341

Бренды по названию

Популярные бренды

Intel 81341, Руководство разработчика

Результаты поиска

Содержание 81341

Отзывы:

Похожие инструкции для 81341

Бренды по названию

Популярные бренды