Intel 81341 Скачать руководство пользователя страница 265

Страница: 265 / 1056

Intel

81341 and 81342 I/O Processors

December 2007

Developer’s Manual

Order Number: 315037-002US

265

Address Translation Unit (PCI Express)—Intel

81341 and 81342

3.8

ATU Queue Architecture

ATU operation and performance depends on queueing mechanism implemented

between internal bus interface and PCI Express interface.

Figure 24

indicates the ATU

queue architecture consists of separate inbound and outbound queues. The function of

each queue is described in the following sections.

3.8.1

Inbound Queues

The inbound data queues of the ATU support transactions initiated on a PCI Express

Link and targeted at either 81341 and 81342 local memory or a 81341 and 81342

memory mapped register.

Table 122

details the name and sizes of the ATU inbound

data queues.

3.8.1.1

Inbound Posted Queue Structure

The ATU Inbound Posted Queues consist of the inbound posted data queue (IPDQ) and

the inbound posted header queue (IPHQ). The inbound posted data queue holds the

data for posted (memory/message) transactions moving from a PCI Express Link to the

internal bus and the header queue holds the corresponding address. The inbound

posted data queue has a queue depth of 4 KBytes and moves posted transactions from

the PCI Express Link to the internal bus. The corresponding header queue, IPHQ, is

capable of holding 8 entries.
The following rules apply to the PCI Express Link interface and govern the acceptance

of data into inbound posted queues:

• Posted transactions are drained from the head of the queue when the master

interface has acquired bus ownership and transaction ordering and priority have

been satisfied (see

Section 3.8.3

). A memory write transaction is considered

drained from the queue when the entire amount of data entered on the PCI Express

Link has been accepted by the internal bus target. Error conditions resulting in the

cancellation of a write transaction only flush the transaction at the head of the data

and address queue. All other transactions within the queues are considered still

valid.

Table 122. Inbound Queues

Queue Mnemonic

Queue Name

Queue Size

(Bytes)

IPDQ

Inbound Posted Data Queue

3.75 KBytes (240 credits)

IPHQ

Inbound Posted Header Queue

16 Headers

INPQ

Inbound Non Posted Queue

8 Headers

a. Non Posted request with data (I/O and Configuration Writes) always use the 3DW header. The

associated data is always 1 DW in size and can be stored the 4th DW of the header queue.

ICPLDQ

Inbound Completion Data Queue

4 KBytes (infinite credits)

b. As a PCI Express endpoint the ATU must pre-allocate buffer space before issuing a read request. The

ATU is required to advertise infinite credits.

ICPLHQ

Inbound Completion Header Queue

4 Headers (infinite)

Содержание 81341

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 81341

Отзывы:

Похожие инструкции для 81341

Бренды по названию

Популярные бренды

Intel 81341, Руководство разработчика

Результаты поиска

Содержание 81341

Отзывы:

Похожие инструкции для 81341

Бренды по названию

Популярные бренды