Intel 81341 Скачать руководство пользователя страница 107 | Manualshive

Страница: 107 / 1056

background image

Intel

®

81341 and 81342 I/O Processors

December 2007

Developer’s Manual

Order Number: 315037-002US

107

Address Translation Unit (PCI-X)—Intel

®

81341 and 81342

2.7.3.7

Outbound Read Completion Uncorrectable Data Errors

As a target, the ATU may encounter this error when operating in the PCI-X mode.
Uncorrectable Data errors occurring during read completion transactions that are

claimed by the ATU are recorded,

PERR#

is asserted (when enabled) and

SERR#

is

asserted (when enabled). Specifically, the following actions with the given constraints

are taken by the ATU:

•

PERR#

is asserted two clocks cycles (three clock cycles when operating in the PCI-

X mode) following the data phase in which the uncorrectable data error is detected

on the bus. This is only done when the Parity Error Response bit in the ATUCMD is

set. When the ATU asserts

PERR#

, additional actions are taken:

— The Master Parity Error bit in the ATUSR is set.

— When the ATU PCI Master Parity Error Interrupt Mask Bit in the ATUIMR is clear,

set the PCI Master Parity Error bit in the ATUISR. When set, no action.

— When the

SERR#

Enable bit in the ATUCMD is set, and the Uncorrectable Data

Error Recover Enable bit in the PCIXCMD register is clear, assert

SERR#

,

otherwise no action. When the ATU asserts

SERR#,

additional actions are

taken:

Set the

SERR#

Asserted bit in the ATUSR.

When the ATU

SERR#

Asserted Interrupt Mask Bit in the ATUIMR is clear, set

the

SERR#

Asserted bit in the ATUISR. When set, no action.

When the ATU

SERR#

Detected Interrupt Enable Bit in the ATUCR is set, set

the

SERR#

Detected bit in the ATUISR. When clear, no action.

— The read completion is aborted on the internal bus of the 81341 and 81342.

• The Detected Parity Error bit in the ATUSR is set. When the ATU sets this bit,

additional actions are taken:

— When the ATU Detected Parity Error Interrupt Mask bit in the ATUIMR is clear,

set the Detected Parity Error bit in the ATUISR. When set, no action.

• For PCI-X Mode 2, update the

“ECC Control and Status Register - ECCCSR” on

“ECC First Address Register - ECCFAR” on page 203

Second Address Register - ECCSAR” on page 204

, and the

“ECC Attribute Register -

ECCAR” on page 205

for the transaction.

«
...
105
106
107
108
109
...
»

Содержание 81341

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 81341

Бренд: IDT Страницы: 281

DMX-Universal-Demux

Бренд: DMX4ALL Страницы: 17

Бренд: Rockwell Automation Страницы: 108

Бренд: Telit Wireless Solutions Страницы: 113

PCH1 T P Series

Бренд: Parker Страницы: 107

Super Sound Set SR-JV80-07

Бренд: Roland Страницы: 8

Бренд: Schrack Technik Страницы: 2

Thin Client US310e

Бренд: NEC Страницы: 6

Бренд: ZALMAN Страницы: 11

Бренд: ZALMAN Страницы: 18

Бренд: Procool Страницы: 2

Бренд: Sony Ericsson Страницы: 93

Бренд: LUX LUMEN Страницы: 41

Бренд: Intel Страницы: 54

Бренд: sound4 Страницы: 66

Бренд: VIA Technologies Страницы: 25

Бренд: MCT Страницы: 12

Бренд: Renesas Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды