Intel 81341 Скачать руководство пользователя страница 205

Страница: 205 / 1056

Intel

81341 and 81342 I/O Processors

December 2007

Developer’s Manual

Order Number: 315037-002US

205

Address Translation Unit (PCI-X)—Intel

81341 and 81342

2.13.60 ECC Attribute Register - ECCAR

When the ECC Error Phase register (bits 6:4 of the ECCCSR) is non-zero (indicating

that an error has been captured), the ECCAR register indicates the contents of the

P_AD[31:0]

bus (for 64- and 32-bit buses) for the attribute phase of the transaction

that included the error. When the ECC Error Phase register is zero, the contents of this

Note:

Registers that store information from the failing transaction always store information

directly from the bus (uncorrected), even when correction of the error is possible.

Note:

The

“ECC Control and Status Register - ECCCSR”

“ECC First Address Register -

ECCFAR”

“ECC Second Address Register - ECCSAR”

, and

“ECC Attribute Register -

ECCAR”

report the actual transaction that has the error. For example, when the Split

Completion of an original Outbound Read request had an error, the information

regarding the Split Completion is reported.

2.13.61 CompactPCI Hot-Swap Capability ID Register

The following register block provides support of CompactPCI* Hot-Swap functionality.

Table 83. ECC Attribute Register - ECCAR

Bit

Default

Description

31:00 0000 0000H ECC Attribute - This register represents contents of the

P_AD[31:0]

bus (for 64- and 32-bit buses) for

the attribute phase of a failing transaction.

PCI

IOP

Attributes

Attribute Legend:

RV = Reserved

PR = Preserved

RS = Read/Set

RW = Read/Write

RC = Read Clear

RO = Read Only

NA = Not Accessible

+0E4H

Table 84. HS_CAPID - Hot-Swap Cap ID

Bit

Default

Description

07:00

06h

Identifier (ID):

06h, identifying this linked list structure as being the Compact PCI Hot-Swap register block.

PCI

IOP

Attributes

Attribute Legend:

RV = Reserved

RW = Read/Write

RO = Read Only

RT = Read/Toggle

RC = Read/Clear

SW = SROM Write

NA = Not Accessible

+0E8H

Содержание 81341

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 81341

Отзывы:

Похожие инструкции для 81341

Бренды по названию

Популярные бренды

Intel 81341, Руководство разработчика

Результаты поиска

Содержание 81341

Отзывы:

Похожие инструкции для 81341

Бренды по названию

Популярные бренды