Huawei ECC800-Pro Скачать руководство пользователя страница 79

Страница: 79 / 368

Indicators

Table 3-61 ETH converter indicators

Indicator Color

Name

Status

Description

PWR

Green Power input

status

indicator

Steady on

The power input is normal.

Off

There is no power input.

RUN

Green Operating

status

indicator

Off

The power supply is

abnormal.

Blinking at

long

intervals

The ETH converter

successfully registers with

the ECC800-Pro and the

software runs properly (the

indicator blinks at 0.5 Hz, on

for 1s and then off for 1s).

Blinking at

short

intervals

The communication fails or

the ETH converter fails to

(the indicator blinks at 4 Hz,

on for 0.125s and then off

for 0.125s).

Blinking

The indicator blinks at super

short intervals for 0.5s

(blinking at 10 Hz, on for

0.05s and then off for 0.05s)

and then turns off for 0.5s.

The cycle lasts for 10s.

ALM

Red

Alarm

indicator

Steady on

A system failure alarm is

generated.

Off

No system alarm is

generated.

3.2.18 PAD

The pad allows the wireless access from the data center management system. You

can monitor the equipment in the data center and environmental parameters in

real time over the app. The recommended model is T5-10.

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

3 Device Description

Issue 02 (2020-09-07)

Содержание ECC800-Pro

















































































































































































































































































































































































Результаты поиска

Содержание ECC800-Pro

Отзывы:

Похожие инструкции для ECC800-Pro

Бренды по названию

Популярные бренды

Huawei ECC800-Pro, Руководство пользователя

Результаты поиска

Содержание ECC800-Pro

Отзывы:

Похожие инструкции для ECC800-Pro

Бренды по названию

Популярные бренды