Huawei ECC800-Pro Скачать руководство пользователя страница 186

Страница: 186 / 368

Parameter

Description

Encoding

protocol

Set the coding protocol based on the site requirements.

The options are as follows:
– H.264: The H.264 protocol requires relatively small

bandwidth to ensure video quality.

– MJPEG: The MJPEG protocol decodes and displays

each frame independently without referring to the

previous and next frames. This protocol has a small

compression ratio and requires large bandwidth to

ensure video quality. This protocol is suitable for

video editing.

– H.265: The H.265 protocol is bandwidth-conserving

compared with the H.264 protocol.

Encoding

complexity

The options of H.264 profiles include Base profile, Main

profile, and High profile. Among these profiles, the

baseline profile has the lowest encoding compression

performance and lowest requirements on hardware

decoding performance, while the high profile has the

highest.

Resolution

A higher resolution indicates clearer images and higher

bandwidth consumption.

Bit rate type

This parameter is available only when you set Encoding

protocol to H.264 or H.265.
The bit rate is measured by data bits transmitted in a

unit of time.
– Variable bit rate: The bit rate varies depending on

the image complexity to ensure the clarity of images

with great dynamic changes. The bit rate is low if the

image is simple or static. The variable bit rate is

recommended.

– Constant bit rate: The constant bit rate remains the

same. The upper limit of the instantaneous bit rate is

set to 110%. If the bit rate is incorrectly configured

for images with great dynamic changes, the images

will be unclear.

Max. bit rate

This parameter is available only when you set Bit rate

type to Variable bit rate.
The bit rate range depends on the selected resolution.

Bit rate value

Average bit rate when Bit rate type is set to Constant

bit rate.
The bit rate range depends on the selected resolution.

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

6 Feature Description

Issue 02 (2020-09-07)

175

Содержание ECC800-Pro

















































































































































































































































































































































































Результаты поиска

Содержание ECC800-Pro

Отзывы:

Похожие инструкции для ECC800-Pro

Бренды по названию

Популярные бренды

Huawei ECC800-Pro, Руководство пользователя

Результаты поиска

Содержание ECC800-Pro

Отзывы:

Похожие инструкции для ECC800-Pro

Бренды по названию

Популярные бренды