Huawei ECC800-Pro Скачать руководство пользователя

Страница: 44 / 368

The emergency button or emergency door release button is used to open a door in

emergencies.
●

The emergency button can disconnect the power supply to the lock and

therefore unlock the door in case of emergency.

●

In case of emergency, break the glass of the emergency door release button

to disconnect the power supply to the lock and therefore unlock the door.

3.2.4.1.1 Access Actuator

The access actuator is the control component for the aisle door in a smart module.

It connects to the ECC800-Pro controller over FE port, wireless networking

(802.15.4). It opens the magnetic lock by detecting the card swiping information

of the card reader, door open button information, and fire linkage information. It

has access right management, access event record, and alarm record functions.

Figure 3-10 Access actuator

(1) 48 V power port

(2) PoE port

(3) RS485 port COM2

(4) RS485 port COM1

(5) Address DIP switch

(6) Status indicator

(7) BLINK button

(8) WG_2 Wiegand interface (9) WG_1 Wiegand interface

(10) AI/DI_2 dry contact

(reserved port for linkage

control or third-party fire

extinguishing system dry

contacts)

(11) AI/DI_1 dry contact

(reserved port for exit

button)

(12) LOCK/GND/GATE/COM door

status or magnetic lock port

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

3 Device Description

Issue 02 (2020-09-07)

Содержание ECC800-Pro

















































































































































































































































































































































































Результаты поиска

Содержание ECC800-Pro

Отзывы:

Похожие инструкции для ECC800-Pro

Бренды по названию

Популярные бренды

Huawei ECC800-Pro, Руководство пользователя

Результаты поиска

Содержание ECC800-Pro

Отзывы:

Похожие инструкции для ECC800-Pro

Бренды по названию

Популярные бренды