Huawei ECC800-Pro Скачать руководство пользователя страница 165

Страница: 165 / 368

6.5.3.3 Commissioning a C3220 Camera

Prerequisites

●

If multiple cameras are connected, commission one camera first and then

commission other cameras in the same way.

●

The camera has connected to the smart ETH gateway and the smart ETH

gateway communicates properly with the ECC800-Pro.

●

The camera software version is later than SDC 8.0.RC111.

Context

●

Before commissioning the C3220 camera, set the IP address for the C3220

camera based on customer requirements.

●

Configure the camera or VCN internal IP address and the IP address of the

LAN port on the ECC800-Pro in the same network segment.

●

Configure the camera or VCN external IP address and the IP address of the

WAN_1 port on the ECC800-Pro in the same network.

●

Set the internal and external IP addresses as planned by the customer. The

following IP addresses are for reference only.

Table 6-22 IP address planning

Device

Internal IP Address

External IP Address

Camera

Example: 192.168.248.50; range:

192.168.248.50–192.168.248.199

Camera external IP

address

NOTE

The 192.168.246.X

network segment

cannot be set.

VCN

Example: 192.168.248.51; range:

192.168.248.50–192.168.248.199

VCN external IP

address

NOTE

The 192.168.246.X

network segment

cannot be set.

Procedure

Step 1 Log in to the camera web system and enable ONVIF.

1. Remove the network cables that connect the smart ETH gateway to the LAN1

and LAN2 ports on the ECC800-Pro.

2. Use a network cable to connect the PC to the PoE port on the smart ETH

gateway. Then, set the local IP address of the PC to 192.168.0.11.

3. Remove the camera shell and press the reset button for 6s to 10s to restart

the camera.

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

6 Feature Description

Issue 02 (2020-09-07)

154

Содержание ECC800-Pro

















































































































































































































































































































































































Результаты поиска

Содержание ECC800-Pro

Отзывы:

Похожие инструкции для ECC800-Pro

Бренды по названию

Популярные бренды

Huawei ECC800-Pro, Руководство пользователя

Результаты поиска

Содержание ECC800-Pro

Отзывы:

Похожие инструкции для ECC800-Pro

Бренды по названию

Популярные бренды