Huawei ECC800-Pro Скачать руководство пользователя

Страница: 214 / 368

6.7.1 Connecting a Communications Cable

Procedure

Step 1 Connect the T/H sensor to the COM1 port on the ECC800-Pro using a network

cable.

Step 2 Connect the infrared remote control module to the T/H sensor using a network

cable.

----End

6.7.2 Setting and Adding an Infrared Remote Control Module

Prerequisites

●

The infrared remote control module is connected to the ECC800-Pro, and both

are powered on.

●

You have obtained the IP address of the ECC800-Pro as well as the user name

and password used for WebUI login.

●

You have prepared a PC with an IP address in the same network segment as

that of the ECC800-Pro, and the PC is connected to the WAN port on the

ECC800-Pro.

Context

After an infrared remote control module is replaced, you need to add the new

infrared remote control module on the ECC800-Pro WebUI.

Procedure

Step 1 Set monitoring parameters for the infrared remote control module.

1. Set the device address to 2 by setting the DIP switch on the infrared remote

control module.

Table 6-39

describes how to set the DIP switch.

The DIP switch consists of toggle switches 1–5 (from left to right). Toggle

switches 1–4 specify the address of the infrared remote control module.

Toggle switch 5 specifies the address of the RS485 build-out resistor. 0

indicates OFF and 1 indicates ON. Toggle switch 5 is set to OFF.

Table 6-39 Setting a device address

Address

Toggle

Switch 1

Toggle

Switch 2

Toggle

Switch 3

Toggle

Switch 4

OFF

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

6 Feature Description

Issue 02 (2020-09-07)

203

Содержание ECC800-Pro

















































































































































































































































































































































































Результаты поиска

Содержание ECC800-Pro

Отзывы:

Похожие инструкции для ECC800-Pro

Бренды по названию

Популярные бренды

Huawei ECC800-Pro, Руководство пользователя

Результаты поиска

Содержание ECC800-Pro

Отзывы:

Похожие инструкции для ECC800-Pro

Бренды по названию

Популярные бренды