Huawei ECC800-Pro Скачать руководство пользователя | Manualshive

Страница: 203 / 368

background image

NO TE

Click Link high temperature with skylight open on the Linkage Group tab page. If it is in on

state, the corresponding logic configurations on the Linkage Logic List tab page are available. If

it is in off state, the corresponding logic configurations on the Linkage Logic List tab page are

unavailable.

----End

Follow-up Procedure

After the alarm has been cleared when high temperature linkage occurs, perform

the following operations: Close the skylights manually.

6.6.1.3 (Optional) Commissioning an Intelligent Aisle Light

Prerequisites

The upstream power input circuit breaker of the AC actuator is turned on.

Context

After the intelligent aisle lighting is set successfully, perform the following steps:

●

After the door is opened using the access control system, the lighting is

turned on.

NO TE

An access control system is involved in the scenario.

●

In the smart module aisle, the lighting is turned on when a camera and a

multi-functional sensor detect that someone enters.

●

The lighting is turned off when the camera and the multi-functional sensor

fail to detect any person in the aisle within 10 minutes.

NO TE

When using the intelligent lighting function, pay attention to the following:
● If a foreign object is hung on the skylight ceiling of the smart module and when the foreign

object moves, the camera may mistakenly generate a motion detection alarm to change the

lighting status.

● When the human body moves, the camera generates a motion detection alarm and the

lighting is turned on. If the motion amplitude of the human body is small, the camera

cannot generate the motion detection alarm. If the lighting is turned off due to this reason,

wave to the camera and the lighting is turned on again.

● If light greatly changes outside the smart module, the camera may mistakenly generate a

motion detection alarm and the lighting is mistakenly turned on.

● If you manually turn off the lighting when you leave the smart module, the lighting may be

turned on again when the camera detects that the person leaves.

● The effective detection distance of the multi-functional sensor is 2.5 m.

Procedure

Step 1 Log in to the ECC800-Pro WebUI as an administrator.

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

6 Feature Description

Issue 02 (2020-09-07)

Copyright © Huawei Technologies Co., Ltd.

192

«
...
201
202
203
204
205
...
»

Содержание ECC800-Pro

















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ECC800-Pro

Бренд: Panasonic Страницы: 45

Бренд: Mackie Страницы: 16

Бренд: TANDBERG Страницы: 47

Бренд: National Instruments Страницы: 40

Бренд: National Instruments Страницы: 28

Бренд: National Instruments Страницы: 7

Бренд: National Instruments Страницы: 22

Бренд: Keba Страницы: 16

Бренд: KEB Страницы: 16

Бренд: Wang Страницы: 68

Бренд: NAVITAS Страницы: 14

Бренд: MaintTech Страницы: 28

Бренд: WAGNER Страницы: 128

SAE 07.2 Series

Бренд: AUMA Страницы: 116

Бренд: Fibocom Страницы: 79

Бренд: oventrop Страницы: 40

Бренд: REGLOPLAS Страницы: 44

Бренд: Sentiotec Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды