Huawei ECC800-Pro Скачать руководство пользователя

Страница: 261 / 368

Path: Maintenance > Configuration File > Back Up Current Settings

NO TE

If the main control module is damaged, you may fail to log in to the ECC800-Pro. In this case,

you cannot back up the settings.
The following information cannot be backed up: monitoring module IP address parameters,

smart module certificate, NetEco certificate, NetEco second-challenge password, time

configuration parameters, access user management, access permission management, device

access certificate, log, and user configuration information.

Step 2 Label each cable and antenna based on the corresponding ports on the ECC800-

Pro main control module.

Step 3 Remove cables, USB flash drive, USB-to-WiFi module, and antennas from the

ECC800-Pro main control module.

Step 4 Loosen the screws on both sides of the ECC800-Pro main control module and pull

the handles on both sides of the ECC800-Pro main control module to remove the

main control module.

Figure 7-1 Removing the ECC800-Pro main control module

Step 5 (Optional) Remove the SIM card from the corresponding slots of the ECC800-Pro

main control module.

Step 6 (Optional) Install the removed SIM card in the corresponding slot of the new

ECC800-Pro main control module.

Figure 7-2 Installing a SIM card

Step 7 Install the spare ECC800-Pro main control module in the ECC800-Pro subrack and

tighten the screws on both sides of the ECC800-Pro main control module.

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

7 Maintenance

Issue 02 (2020-09-07)

250

Содержание ECC800-Pro

















































































































































































































































































































































































Результаты поиска

Содержание ECC800-Pro

Отзывы:

Похожие инструкции для ECC800-Pro

Бренды по названию

Популярные бренды

Huawei ECC800-Pro, Руководство пользователя

Результаты поиска

Содержание ECC800-Pro

Отзывы:

Похожие инструкции для ECC800-Pro

Бренды по названию

Популярные бренды