Huawei ECC800-Pro Скачать руководство пользователя страница 155

Страница: 155 / 368

LAN Switch Networking Scenario

If there are multiple VCNs for multiple smart modules, you are advised to evenly

distribute the cameras to each VCN.

Figure 6-9 VCN connecting to the LAN switch

6.5.3 Commissioning a Camera (Smart ETH Gateway

Networking Scenario)

6.5.3.1 Commissioning IPC6325 Cameras

Prerequisites

●

If multiple cameras are accessed, retain the connection of one camera and

disconnect connections from other cameras. After commissioning the

connected camera, commission other cameras in the same way.

●

The camera has connected to the smart ETH gateway and the smart ETH

gateway communicates properly with the ECC800-Pro.

●

The camera software version is later than V500R019C30.

Context

●

Before commissioning the IPC6325 camera, set the IP address for the IPC6325

camera based on customer requirements.

●

Configure the camera or VCN internal IP address and the IP address of the

LAN port on the ECC800-Pro in the same network segment.

●

Configure the camera or VCN internal IP address and the IP address of the

WAN_1 port on the ECC800-Pro in the same network.

●

Set the internal and external IP addresses as planned by the customer. The

following IP addresses are for reference only.

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

6 Feature Description

Issue 02 (2020-09-07)

144

Содержание ECC800-Pro

















































































































































































































































































































































































Результаты поиска

Содержание ECC800-Pro

Отзывы:

Похожие инструкции для ECC800-Pro

Бренды по названию

Популярные бренды

Huawei ECC800-Pro, Руководство пользователя

Результаты поиска

Содержание ECC800-Pro

Отзывы:

Похожие инструкции для ECC800-Pro

Бренды по названию

Популярные бренды