Huawei ECC800-Pro Скачать руководство пользователя

Страница: 224 / 368

–

Blinking at short intervals: The indicator is on for 0.125 seconds and then

off for 0.125 seconds alternately.

Procedure

Step 1 Press the networking switch on the iBOX for 2 seconds. The ALM indicator blinks

red once, and the RF_Z indicator turns from steady green to blinking green at

super short intervals, which indicates that the iBOX is being networked.

Step 2 Press the iBAT networking switch for 2 seconds. When the RUN/ALM indicator

turns from steady red to blinking green at super short intervals (iBattery 2.0) or

short intervals (iBattery 3.0), and finally to blinking green at long intervals, the

iBAT connects to the iBOX network.

NO TE

● It is recommended that iBATs be networked from the positive battery string terminal

according to the battery cable connection sequence.

● Batteries are numbered depending on the sequence of connecting iBATs to the iBOXs.

Step 3 Perform networking operations on the next iBAT only after networking for the

previous iBAT is successful. Repeat

Step 2

to add other iBATs to the iBOX network.

Step 4 Press the iBOX networking switch for 2 seconds. When the RF_Z indicator on the

iBOX turns from blinking green at super short intervals to blinking green at long

intervals, the networking is complete.

NO TE

After the networking is complete, if the ALM indicator on the iBOX is steady on, the

number of devices online is smaller than the value of iBAT Number. Check that iBAT

Number is set to a correct value and that the iBAT is successfully networked.

Step 5 (Optional) If multiple iBOXs are cascaded, repeat

Step 1

Step 4

to perform

networking for remaining iBOXs and iBATs.

----End

6.9.3 Battery Shallow Discharge Test

To facilitate O&M, you can configure a battery shallow discharge test on the

Linkage Control tab page.

Prerequisites

Only the UPS2000-G-(6 kVA–10 kVA) and UPS2000-G-3 kVA (dual-live wire)

support a battery shallow discharge test on the ECC800-Pro.
You need to manually configure the battery shallow discharge test based on

requirements.
The system type is FusionModule500.

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

6 Feature Description

Issue 02 (2020-09-07)

213

Содержание ECC800-Pro

















































































































































































































































































































































































Результаты поиска

Содержание ECC800-Pro

Отзывы:

Похожие инструкции для ECC800-Pro

Бренды по названию

Популярные бренды

Huawei ECC800-Pro, Руководство пользователя

Результаты поиска

Содержание ECC800-Pro

Отзывы:

Похожие инструкции для ECC800-Pro

Бренды по названию

Популярные бренды