Huawei ECC800-Pro Скачать руководство пользователя страница 57

Страница: 57 / 368

Item

Specifications

Address DIP

switch

4-pin address DIP switch (reserved)

Fuse

16 A, 250 V AC

Spare fuse box

Two 16 A, 250 V AC fuses

E-label

Supported

Indicators

Table 3-40 Indicators

Indicator Color

Name

Status

Description

Power

Green Power input

status

indicator

Steady on

The power input is normal.

Off

There is no power input.

RUN

Green Running

status

indicator

Off

The power is abnormal or

the board program is

Blinking at

long

intervals

The smart module actuator

successfully registers with

the ECC800-Pro and the

software runs properly (the

indicator blinks at 0.5 Hz, on

for 1s and then off for 1s).

Blinking at

short

intervals

The communication fails or

the smart module actuator

fails to register with the

ECC800-Pro (the indicator

blinks at 4 Hz, on for 0.125s

and then off for 0.125s).

Blinking

The indicator blinks at super

short intervals for 0.5s

(blinking at 10 Hz, on for

0.05s and then off for 0.05s)

and then turns off for 0.5s.

The cycle lasts for 5s.

ALM

Red

Alarm

indicator

Steady on

A system failure alarm is

generated.

Off

No system alarm is

generated.

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

3 Device Description

Issue 02 (2020-09-07)

Содержание ECC800-Pro

















































































































































































































































































































































































Результаты поиска

Содержание ECC800-Pro

Отзывы:

Похожие инструкции для ECC800-Pro

Бренды по названию

Популярные бренды

Huawei ECC800-Pro, Руководство пользователя

Результаты поиска

Содержание ECC800-Pro

Отзывы:

Похожие инструкции для ECC800-Pro

Бренды по названию

Популярные бренды