Huawei ECC800-Pro Скачать руководство пользователя страница 45

Страница: 45 / 368

Specifications

Table 3-28 Access actuator technical specifications

Item

Specifications

Power input

● DC input: terminal, with an input voltage of 36 V DC–60 V

● PoE power supply: one PoE port that complies with

IEEE802.3at

PoE port

FE communication with the rate of 10/100 Mbit/s

Wireless

communicati

One wireless communication port that complies with IEEE

802.15.4, mutual backup with FE communication

AI/DI port

Two AI/DI ports, can connect to the fire alarm and exit button

DO/DI port

● One 12 V DC power output that controls magnetic locks,

terminal

● One DI input port for connecting to the door status switch

RS485 serial

port

expansion

Two RS485 ports (one route) with the default communication

rate of 9600 bit/s, physical port cascading supported (reserved

function)

Wiegand port Two Wiegand ports, 12 V DC card reader operating power

output; two routes of card readers can operate at the same

time.

BLINK button ● Press the button for less than 1 second to start blinking.

● Hold down the button for 1–5 seconds to search for a

network and start networking.

● Hold down the button for more than 10 seconds to clear

network parameters.

Address DIP

switch

4-pin address DIP switch

E-label

Supported

Indicators

Table 3-29 Access actuator indicators

Indicator Color

Name

Status

PWR

Green

Power input

status

indicator

● Steady on: The power input is normal.
● Off: There is no power input.

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

3 Device Description

Issue 02 (2020-09-07)

Содержание ECC800-Pro

















































































































































































































































































































































































Результаты поиска

Содержание ECC800-Pro

Отзывы:

Похожие инструкции для ECC800-Pro

Бренды по названию

Популярные бренды

Huawei ECC800-Pro, Руководство пользователя

Результаты поиска

Содержание ECC800-Pro

Отзывы:

Похожие инструкции для ECC800-Pro

Бренды по названию

Популярные бренды