Huawei ECC800-Pro Скачать руководство пользователя страница 219

Страница: 219 / 368

3. Set Device to ECC800, Performance data to Total electrical energy of

system IT load output, and Statistics mode to Hour, set other query criteria

such as Start time and End time as required, and click Query. Record the

increment in total electrical energy of system IT load output of the ECC800-

Pro. Increment in total electrical energy of system IT load output = 56.0 kWh

– 50.0 kWh = 6.0 kWh.

Figure 6-63 Querying the total electrical energy of system IT load output

4. Calculate the PUE of the smart module. PUE = Increment in total system input

electrical energy/Increment in total electrical energy of system IT load output

= 10.0 kWh/6.0 kWh = 1.67.

6.8.2 Configuring PUE User-defined Mode

Context

This section describes how to configure PUE for the integrated PDU connected.

The functions of configuration buttons for the PUE user-defined mode are

described as follows.

Table 6-42 PUE configuration buttons

No.

Button

Description

Add

Adds new total power consumption or IT power consumption

parameters.

Delete

Deletes a parameter setting for the total power consumption

or IT power consumption.

Procedure

Step 1 Log in to the ECC800-Pro WebUI as an administrator.

Step 2 Choose System Settings > PUE Configuration.

Step 3 Set PUE function to Enable.

Step 4 Set PUE configuration mode to User-defined, and click Submit.

1. On the Total Power Consumption Configuration tab page, click Add to

enter the Total Power Consumption Configuration page. On the Select

Device tab page, select Integrated PDU 1. On the Select Indicators tab

page, select Total active electricity energy of PDU input, and click Confirm.

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

6 Feature Description

Issue 02 (2020-09-07)

208

Содержание ECC800-Pro

















































































































































































































































































































































































Результаты поиска

Содержание ECC800-Pro

Отзывы:

Похожие инструкции для ECC800-Pro

Бренды по названию

Популярные бренды

Huawei ECC800-Pro, Руководство пользователя

Результаты поиска

Содержание ECC800-Pro

Отзывы:

Похожие инструкции для ECC800-Pro

Бренды по названию

Популярные бренды