Huawei ECC800-Pro Скачать руководство пользователя страница 33

Страница: 33 / 368

Indicators

Table 3-14 Indicators on the ECC800-Pro main control module

Indicator Color Name

Status

Description

RUN

Green Running status

indicator

Steady on

The power supply is normal,

the program is being loaded.

Off

The power supply is

abnormal.

Blinking at

long

intervals

The software runs properly

(the indicator blinks at 0.5

Hz, on for 1s and then off

for 1s) or the ECC800-Pro

registers with the NetEco

successfully.

Blinking at

short

intervals

The ECC800-Pro does not

(the indicator blinks at 5 Hz,

on for 0.125s and then off

for 0.125s).

ALM

Red

Alarm indicator

Steady on

A system failure alarm is

generated.

Off

The system is normal.

RF_Z

Green Communication

status indicator

Blinking at

long

intervals

A network is set up, and no

node access is allowed (the

indicator blinks at 0.5 Hz, on

for 1s and then off for 1s).

Blinking at

super

short

intervals

A network is set up, and

node access is allowed (the

indicator blinks at 10 Hz, on

for 0.05s and then off for

0.05s).

SW Button

Table 3-15 SW button description

Function

Description

Operation Description

Indicator Status

Wireless

network RF_Z

(802.15.4)

pairing

In non-wireless network (802.15.4)

pairing mode, press and hold down

the button for 3s to 5s to enter the

wireless network pairing mode.

The RF_Z indicator is

blinking at super

short intervals.

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

3 Device Description

Issue 02 (2020-09-07)

Содержание ECC800-Pro

















































































































































































































































































































































































Результаты поиска

Содержание ECC800-Pro

Отзывы:

Похожие инструкции для ECC800-Pro

Бренды по названию

Популярные бренды

Huawei ECC800-Pro, Руководство пользователя

Результаты поиска

Содержание ECC800-Pro

Отзывы:

Похожие инструкции для ECC800-Pro

Бренды по названию

Популярные бренды