Huawei ECC800-Pro Скачать руководство пользователя

Страница: 134 / 368

–

If the connection fails, check whether the cable is properly connected to

the device, whether the device is running properly, and whether the

parameter settings are consistent with the device parameters.

----End

5.9 Commissioning Cabinet Electronic Clasp Lock (for

FusionModule800)

When the system type is FusionModule800 and the cabinet electronic clasp locks

are installed, perform the following steps to configure it.

Prerequisites

●

The cabinet electronic clasp locks of odd- and even-numbered cabinets have

been cascaded in hand-in-hand mode respectively. One end of a network

cable is connected to the RS485_IN port on the first cabinet electronic clasp

lock of an odd-numbered cabinet, and the other end of the cable is connected

to the COM2 port on the ECC800-Pro; one end of another network cable is

connected to the RS485_IN port on the first cabinet electronic clasp lock of an

even-numbered cabinet, and the other end of the cable is connected to the

COM3 port on the ECC800-Pro.

●

The smart module view has been deployed.

●

The cabinet door can be opened and closed properly. If the cabinet door

cannot be opened and closed properly, adjust the position of the cabinet

electronic clasp lock by performing steps 1 and 2.

Procedure

Step 1 (Optional) Check whether the cabinet door lock is leveled to 2000 (+3) mm. If

not, adjust it.

Step 2 (Optional) If the cabinet door still cannot be opened after step 1 is performed,

adjust the position of the cabinet electronic clasp lock by using the slotted holes

until the cabinet door can be opened and closed properly.

Step 3 Set device addresses for cabinet electronic clasp locks.

●

A cabinet electronic clasp lock is installed at the front and rear doors of each

cabinet respectively. The address for the cabinet electronic clasp lock on the

front door is an odd number, and that for the cabinet electronic clasp lock on

the rear door is an even number.

●

The cabinet electronic clasp locks of odd-numbered cabinets are connected in

series. The addresses start from 1, and a maximum of 12 cabinet electronic

clasp locks can be connected in series.

●

The cabinet electronic clasp locks of even-numbered cabinets are connected

in series. The addresses start from 1, and a maximum of 12 cabinet electronic

clasp locks can be connected in series.

●

Set a device address for a cabinet electronic clasp lock by operating the DIP

switch on the cabinet electronic clasp lock. Toggle switches 1 to 6 specify the

device address in binary mode. ON indicates 1, and OFF indicates 0.

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

5 Power-On Commissioning

Issue 02 (2020-09-07)

123

Содержание ECC800-Pro

















































































































































































































































































































































































Результаты поиска

Содержание ECC800-Pro

Отзывы:

Похожие инструкции для ECC800-Pro

Бренды по названию

Популярные бренды

Huawei ECC800-Pro, Руководство пользователя

Результаты поиска

Содержание ECC800-Pro

Отзывы:

Похожие инструкции для ECC800-Pro

Бренды по названию

Популярные бренды