Huawei ECC800-Pro Скачать руководство пользователя

Страница: 39 / 368

Indicator

Status

Description

Blinking

Blinking at super short intervals for 0.5s and then off for

0.5s; last 10s (blinking at super short intervals: 10 Hz,

on for 0.05s and then off for 0.05s)

ALM

Steady

A system fault alarm is raised.

Off

The system is normal.

Table 3-22 BLINK button description

Function

Description

Operation

Description

Indicator Status

Blinking

Press the button for

less than 2s.

The RUN indicator blinks at super

short intervals for 0.5s and then off for

0.5s; last 10s (blinking at super short

intervals for 10 Hz, on for 0.05s and

then off for 0.05s).

3.2.2 Rack Environment Unit

The rack environment unit collects and controls the environmental data of IT

cabinets in the smart module.

Figure 3-8 Rack environment unit

(1) Ground port

(2) 48 V DC power input port (3) PoE port

(4) COM1/12V port

(5) COM2/12V port (6) COM3 port

(7) COM4 port

(8) NTC1–3

(9) NTC4–6

(10) AI/DI_1 port

(11) AI/DI_2 port

(12) 12V_1 port

(13) 12V_2 port

(14) BLINK button

(15) Status indicator

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

3 Device Description

Issue 02 (2020-09-07)

Содержание ECC800-Pro

















































































































































































































































































































































































Результаты поиска

Содержание ECC800-Pro

Отзывы:

Похожие инструкции для ECC800-Pro

Бренды по названию

Популярные бренды

Huawei ECC800-Pro, Руководство пользователя

Результаты поиска

Содержание ECC800-Pro

Отзывы:

Похожие инструкции для ECC800-Pro

Бренды по названию

Популярные бренды