Hioki MR8827 Скачать руководство пользователя страница 397

Страница: 397 / 436

392

Error Messages

Msg

No.

Message

Remedy

References

Cannot set.(External sampling)

Cannot use roll mode when using

external sampling.

Rated capacity/rated output error. Rated capacity/Rated output has

exceeded selected range. Input

correct value.

(p. 154)

Cannot use. (Roll Mode, Wave

Calculation)

If the memory division function is

in use, these functions cannot be

used.

“12.1 Recording Settings”

(p. 239)

No waveform data.

Acquire waveform data.

—

Recording length is too long.

Shorten the measurement

recording length.

The maximum recording length

that can be calculated is 40,000

div.

“3.3.3 Recording Length (Number

of Divisions)” (p. 57)

In key lock.

Keylock is engaged. Cancel the

Key-Lock function.

“KEY LOCK” (p. 17)

LAN: Bad IP address.

Check the IP address.

“16.1 LAN Connection and Settings

(Before Using FTP/

Internet Browser/Command

Communications)” (p. 310)

LAN: Connection timed out.

Check the transmission settings.

LAN: Network error.

Check the connection between

the instrument and connection

destination.

100 Inappropriate setting of time axis

for waveform data.

Return the timebase to the

timebase setting when the

waveform was measured.

“3.3.2 Timebase and Sampling

Rate” (p. 54)

“9.11 Use Trigger Settings to

Search Measurement Data”

(p. 207)

101 Some blocks are different in time

axis setting from the others.

Set the same timebase setting

for all search target blocks.

If they cannot be the same,

set the search range to display

blocks only.

102 Some blocks are different in

modules configuration from the

others.

Unify the modules configuration

of search target blocks.

If they cannot be the same,

set the search range to display

blocks only.

“9.11 Use Trigger Settings to

Search Measurement Data”

(p. 207)

103 No data matching your search

condition.

Check the trigger setting.

104 There is no data in the search

target channel.

Select channels with

measurement data in the search

target.

105 There is a block with no data in

the search target channel.

Select blocks with measurement

data in the search target.

106 Some blocks are different in

measurement mode of modules

from the others.

Blocks with varying measurement

modes cannot be searched.

—

108 Some blocks are different in

measurement mode of modules

from the others.

Set the search range within the

display blocks.

“9.11 Use Trigger Settings to

Search Measurement Data”

(p. 207)

110 No space to store waveform data

at copy location.

Create empty space by deleting

waveform data from copy

location.

(p. 182)

111 No space to register arbitrary

waveform data.

Create empty space by deleting

waveform data from registration

location.

(p. 182)

Содержание MR8827




















































































































































































































































































































































































































































Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды

Hioki MR8827, Инструкция по эксплуатации

Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды