Hioki MR8827 Скачать руководство пользователя страница 219

Страница: 219 / 436

214

Numerical Value Calculation Settings

Parameter Table

Calculation type

Parameter

Parameter description

Period

Frequency

Pulse Width

Pulses

Duty Ratio*

Time Diff

Phase Diff

* Level and Filter only

L (Level)

Calculation is based on the interval (time) when the level is

crossed.

F (Filter)

Only when the measurement signal has crossed the level

and has not crossed the level again within the specified

filter width, it is taken as a valid event. This is useful to

exclude level crossing events caused by noise.

S (Slope [↑, ↓])

Calculation is based on the interval (time) when the level is

crossed.

Depending on this setting, either crossing on the upward

slope (↑) or downward slope (↓) is used for calculation.

Risetime

Falltime

P (%)

Determines which section of the waveform between the

upper and lower limits is used for risetime (or falltime)

calculation.

The range is narrowed from the upper and lower limit values

by the percentage set here.

Time to Lev

L (Level)

Calculates the time specified level is crossed.

F (Filter)

Only when the measurement signal has crossed the level

and has not crossed the level again within the specified

filter width, it is taken as a valid event. This is useful to

exclude level crossing events caused by noise.

S (Slope [↑, ↓])

Determines whether the time is calculated until the signal

crosses the specified level on the upward slope or on the

downward slope.

Lev-time

Time or Measure

(Calculation results)

Specifies the time for calculating the measurement value,

using the trigger position as zero.

To use numerical calculation results, specify the numerical

calculation number.

The range specified by AB cursors is not available.

Calculation

Numerical Calculation

No.

Sets the numerical calculation number.

+, - , ×, ÷

Sets operators for the four basic arithmetic operations.

• Depending on the signal waveform, calculation values for the Period, Frequency, Risetime, and

Falltime parameters may not be displayed.

• When Scaling is enabled, the waveform data is scaled before numerical calculation. The units for

parameter values are derived from the units set for the Scaling function.

About Scaling, refer to: “8.5 Convert Input Values (Scaling Function)” (p. 151).

Содержание MR8827




















































































































































































































































































































































































































































Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды

Hioki MR8827, Инструкция по эксплуатации

Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды