Hioki MR8827 Скачать руководство пользователя страница 114

Страница: 114 / 436

109

Auto-print Settings

6.2 Auto-print Settings

This applies to the Memory, Recorder, and FFT functions.

These settings must be set before starting measurement.

Measurement data will print automatically when you press the

START

key to start measurement. For

printer output, make sure that the recording paper is loaded correctly. For LAN output, make sure that the

PC connected via LAN is prepared.

Procedure

Press the

SYSTEM

key to open the System screen, and then select the

[Printer]

sheet.

Enable auto-print.
(When using the Memory or FFT Functions)

Move the cursor to

[Auto Print]

, and select

[On]

Default setting: Off (no automatic printing)

(When using the Recorder Function)

Move the cursor to

[Realtime Print]

Select

[On]

•

To output waveform data to

the PC connected via LAN

Model 9333 LAN

Communicator must be

installed on the PC to which

the data is to be output.

For more information

about how to operate and

configure the Model 9333

LAN Communicator, as well

as install it on a PC, see the

instruction manual of Model

9333 LAN Communicator.

•

When setting the output

destination to

[LAN]

The IP addresses of the

instrument and the PC

connected via LAN must be

set. For more information

about how to set the IP

addresses, refer to (p. 310).

(When using the Memory or FFT Functions)
Specify the output destination.

Move the cursor to

[Output]

Printer:

LAN:

The data is automatically output to the PC connected

via LAN.

Model 9333 LAN Communicator required.

Printer

The data is automatically printed by the internal

printer. (

Default setting)

LAN:

The data is automatically output to the PC

connected via LAN.

Model 9333 LAN Communicator required.

(When using the Memory Function)
Choose print area settings as required.

Move the cursor to the

[Print Area]

item.

Whole Wave

Print all waveform data in internal memory of the

unit. (

Default setting)

A-B Wave

Print only A and B cursors defined range of

waveform data in the internal memory of the unit.

With the Recorder function, the whole waveform will be printed

during measurement regardless of the print area setting.

Printing (

When Model U8350 Printer Unit is installed

)

Содержание MR8827




















































































































































































































































































































































































































































Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды

Hioki MR8827, Инструкция по эксплуатации

Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды