manualshive.com logo in svg

Hioki MR8827, Инструкция по эксплуатации

Инструкция к счетчику Hioki MR8827 доступна для скачивания бесплатно на manualshive.com. Руководство содержит все необходимые сведения для эффективного использования продукта. Скачайте руководство сейчас и получите полную информацию о функциях устройства.

Поделиться
Скачать
background image

7

Operation Precautions

Handling the Instrument and Modules

DANGER

 

•

Do not exceed the range of the specifications and the rated value of the cable 

or the module. 

Otherwise, the instrument may be damaged or may produce heat, resulting in 

personal injury. 

The maximum rated voltage to earth does not change when an attenuator or 

similar is used at the input. Take the connection method into consideration and 

make sure that the rating is not exceeded.

 

•

To avoid electric shock, ddo not remove the instrument’s cover and the module 

case.  

The internal components of the instrument carry high voltages and may 

become very hot during operation.

WARNING

 

•

To avoid electric shocks, confirm that the module is turned off and the 

connection cables are disconnected before removing or replacing a module.

 

•

To avoid electric shocks, never operate the instrument with a module removed. 

To use the instrument after removing a module, install a blank panel over the 

opening of the removed module.

 

•

To prevent instrument damage or electric shocks, use only the screws for 

securing the module in place that shipped with the instrument.

 

If you lose any screw or find that any screws are damaged, please contact your 

Hioki distributor for a replacement.

CAUTION

 • To avoid damage to the instrument, protect it from physical shock during transport and 

handling. Be especially careful to avoid physical shock from dropping.

 •

The mounting screws must be firmly tightened or the module may not perform as 

specified or may fail.

 • To avoid damaging modules, do not touch the module connectors on this instrument. 

 •Before transporting the instrument, disconnect all cables and remove any CF cards, USB memory sticks, 

and recording paper.

 •When there is no input, the waveform might be unstable due to the induced voltage, but this is not an 

error.

 •This instrument may cause interference if used in residential areas. Such use must be avoided unless the 

user takes special measures to reduce electromagnetic emissions to prevent interference to the reception 

of radio and television broadcasts.

10

9

8

7

6

5

4

3

2

1

Appx.

Index

Содержание MR8827





















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MR8827

Makita KP312 Operating Manual preview
KP312
Бренд: Makita Страницы: 8
VECTECH 190 Instruction Manual preview
190
Бренд: VECTECH Страницы: 5
ABI Attachments Infield Rascal Pro Setup Manual preview
Infield Rascal Pro
Бренд: ABI Attachments Страницы: 8
Abicor Binzel BRS-LC Operating Instruction preview
BRS-LC
Бренд: Abicor Binzel Страницы: 84
ABI Attachments ABI Force Z-23 Product Instruction Sheet preview
ABI Force Z-23
Бренд: ABI Attachments Страницы: 5
abem Terrameter LS User Manual preview
Terrameter LS
Бренд: abem Страницы: 47
Abely LiftMeUp Frequently Asked Questions preview
LiftMeUp
Бренд: Abely Страницы: 5
CAMPAGNOLA HERCULES Quick Manual preview
HERCULES
Бренд: CAMPAGNOLA Страницы: 4
Gearmore T230 Operation, Service And Parts Manual preview
T230
Бренд: Gearmore Страницы: 47
Xtool A30 Pro Manual preview
A30 Pro
Бренд: Xtool Страницы: 51
H-TEC Education D201 Operating Instructions Manual preview
D201
Бренд: H-TEC Education Страницы: 16
H-TEC Education A129 Operating Instructions Manual preview
A129
Бренд: H-TEC Education Страницы: 12
Yanmar RT66 Operator'S Manual preview
RT66
Бренд: Yanmar Страницы: 49
Fagor MX1000 Operating Instruction preview
MX1000
Бренд: Fagor Страницы: 12
Baltic POSEIDON User Manual preview
POSEIDON
Бренд: Baltic Страницы: 68
H&S 2958 Operator'S & Parts Manual preview
2958
Бренд: H&S Страницы: 76
Garmin FUSION APOLLO MS-WB675 Installation Instructions Manual preview
FUSION APOLLO MS-WB675
Бренд: Garmin Страницы: 18
Rapid Shape RS wash Quick Start Manual preview
RS wash
Бренд: Rapid Shape Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды