Hioki MR8827 Скачать руководство пользователя страница 48

Страница: 48 / 436

Load Instrument With Recording Paper (When Model U8350 Printer Unit is installed)

2.4 Load Instrument With Recording Paper (When

Model U8350 Printer Unit is installed)

Read “Handling the Printer and Recording Paper” (p. 8) carefully.

Procedure

Required items: Model MR9231 Recording Paper, Paper

roll axle (Supplied with the instrument)

Press the button to open the printer cover.

Paper roll axle

Insert the paper roll axles into the core of Model 9321

Recording Paper.

Load the instrument with the paper, putting it into the

holder.

Put the right side of the paper first into the holder, and then

press its left side until it clicks, pressing it rightward.

Face the print side of the paper frontward. Putting the

paper in the holder without the paper roll axle installed

will make the printer cover impossible to be opened,

resulting in damage to the printer.

Pull out the edge of the paper toward the other side,

and close the printer cover, pressing the edge face of

the paper against the cover’s side surface.

The surface of the paper may become sticky from the

residue left behind by the adhesive tape and cause

the printing on that area to become unreadable. Unroll

approximately the first 200 mm of paper before inserting

it into the printer.

How to withdraw the recording paper

As shown in the left figure, withdraw the paper, pressing the

paper roll axle rightward.

Measurement Preparation

Содержание MR8827




















































































































































































































































































































































































































































Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды

Hioki MR8827, Инструкция по эксплуатации

Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды