Hioki MR8827 Скачать руководство пользователя страница 199

Страница: 199 / 436

194

Analog Signal Triggers

About period range settings

The period range settings for period triggering depend on the sampling period (sampling rate). (Changing

the timebase also changes the period setting range.)

The [Sampling Rate] setting can be verified on the Status screen -

[Status]

sheet.

The upper threshold of the period range cannot be set below the lower threshold, and vice-versa.

Lower threshold: can be set either to zero, or to at least five times the sampling period.

Upper threshold: can be set to no more than 20,000 times the sampling period.

To apply a trigger when the frequency increases (shorter period) above the upper threshold

Set the period trigger type to

[Per.I]

and the lower threshold to

[0]

. The lower threshold will be ignored

and triggering will occur when the frequency exceeds the upper threshold.

To apply a trigger when the frequency decreases (longer period) below the upper threshold

Set the period trigger type to

[Per.O]

and the lower threshold to

[0]

. The lower threshold will be ignored

and triggering will occur when the frequency drops below the upper threshold.

About the trigger point of the Out-of-Period trigger

Triggering occurs when the period of sequential crossings of the specified reference voltage exceeds the

period range.

The point at which triggering occurs depends on the specified period range and the period of the

measured signal.

When the input signal period is shorter than the specified lower threshold (Trigger Slope: ↑)

Reference

Voltage Level

Lower Threshold

Input Signal

Period

Triggering occurs when the rising edge (↑ trigger slope) of

the input signal crosses the reference voltage level, before

reaching the lower period threshold.

When the input signal period is longer than the specified upper threshold (Trigger Slope: ↑)

Reference

Voltage Level

Upper Threshold

Input Signal

Period

Triggering occurs when the upper threshold period is reached,

before the rising edge (↑ trigger slope) of the input signal

crosses the reference voltage level.

The trigger point is determined by the upper threshold of the

period range.

Содержание MR8827




















































































































































































































































































































































































































































Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды

Hioki MR8827, Инструкция по эксплуатации

Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды