Hioki MR8827 Скачать руководство пользователя страница 31

Страница: 31 / 436

Install or Remove Modules

2.1 Install or Remove Modules

Read “Handling the Instrument and Modules” (p. 7) carefully.

Modules specified when the instrument is ordered are supplied preinstalled. Use the following procedures

to add, replace, or remove modules from the instrument.

•

Up to two logic units can be installed as units 1 to 8. Logic units installed as the other units

cannot be used. Other logic units being installed will be disabled.

•

For information on the analog channel resolution when logic channels are used, refer to “8.10

Detailed Settings for Modules” (p. 164).

To Install a Module

Back side

Required items: One Phillips-head screwdriver (No. 2)

Turn off the power to the instrument.

Correctly orient the module and insert it firmly all the way in.

Make certain that the labels on the module's panel face the same

direction as the labels on the back side of the instrument.

Using a Phillips screwdriver, tighten the two module mounting

screws (M3 × 7.5 mm).

To Remove a Module

Handle

(Example: 8966)

Back side

Required items: One Phillips-head screwdriver (No. 2)

Turn off the power to the instrument.

Remove any connection cables or thermocouples connected to

the module.

Remove the power cord.

Using a Phillips screwdriver, loosen the two module mounting

screws (M3 × 7.5 mm).

Grasp the handles and pull the module out.

If not Installing Another Module After Removal

Back side

Blank

panel

Install a blank panel.

Using a Phillips screwdriver, tighten the two mounting screws

(M3 × 7.5 mm).

Measurements made without a blank panel installed may fail to meet

specifications because of temperature instability within the module.

Содержание MR8827




















































































































































































































































































































































































































































Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды

Hioki MR8827, Инструкция по эксплуатации

Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды