Hioki MR8827 Скачать руководство пользователя страница 178

Страница: 178 / 436

173

Detailed Settings for Modules

8.10.8 Setting Model MR8990 Digital Voltmeter Unit

• When the Model MR8990 Digital Voltmeter Unit is installed as unit 1, 2, 9, or 10, the standard logic

channels cannot be used.

• The resolution of the data measured by the recorder function is 16 bits.

Refer to “To Open [Each Ch] and Make a Channel Selection” (p. 164).

Frequency

Set the power frequency.

Set 50 Hz or 60 Hz according to the power frequency for your region.

50Hz

Cycle 20 ms

(Default setting)

60Hz

Cycle 16.67 ms

If the power frequency setting is not configured correctly, measurement values will be unstable.

NPLC

PLC (Power Line Cycle) is the time equivalent to one cycle of the power frequency.

Set the integration time based on one PLC.

0.1 to 0.9, 1

(

Default setting)

to 10, 20, 30, 40, 50, 60, 70, 80, 90, 100

Example: When the power frequency is 50 Hz, and NPLC is set to 10, 20 ms × 10 =

200 ms.

The measurement data refresh rate becomes 200 ms.

Fast response

Data can be refreshed at high speed.

Off

Refreshes data at the integration time set for NPLC.

(Default setting)

Calculates the moving average and refreshes the data at high speed.

Refreshes the data at 0.1 PLC when NPLC is up to 9.

Refreshes the data at 1 PLC when NPLC is 10 or above.

Calibration

This setting is used for performing calibration or synchronization between channels

automatically when measurement is started. Performing synchronization between

channels enables matching the timing for the start of integration.

Off

No calibration and synchronization.

(Default setting)

Perform calibration and synchronization.

Synchronization Perform only synchronization between channels.

Utility Functions

Содержание MR8827




















































































































































































































































































































































































































































Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды

Hioki MR8827, Инструкция по эксплуатации

Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды