Hioki MR8827 Скачать руководство пользователя страница 388

Страница: 388 / 436

383

Maintenance and Service

WARNING

•

Do not touch the internal parts of this instrument as high voltage is generated

in some parts. Customers are not allowed to modify, disassemble, or repair the

instrument. Doing so may cause fire, electric shock, or injury.

•

Do not touch the internal parts of this instrument as high voltage is generated

in some parts. Customers are not allowed to modify, disassemble, or repair the

instrument. Doing so may cause fire, electric shock, or injury.

The recording paper can be purchased via authorized Hioki distributor or reseller.

Calibrations

The frequency of calibration varies depending on the status of the instrument and installation environment.

We recommend that the frequency of calibration be determined in accordance with the status of the

instrument and installation environment and that you request that calibration be performed periodically.

Precautions During Shipment

Be sure to observe the following precautions:

• To avoid damage to the instrument, remove all accessories and optional equipment from the instrument.

Use the original packing materials in which the product was shipped. Damage that occurs during

transport is not covered by the warranty.

• When sending the instrument for repair, be sure to include details of the problem.

To avoid straining some parts of the printer, and to prevent dirt adhering to the print head, close the printer

cover.

Replaceable Parts and Operating Lifespan

The characteristics of some parts used in the product may deteriorate due to long time of use.

To ensure the product can be used over the long term, it is recommended to replace these parts on a

periodic basis.

Contact your authorized Hioki distributor or reseller for replacement.

The service life of parts varies with the operating environment and frequency of use. Parts are not

guaranteed to operate throughout the recommended replacement cycle.

Part

Recommended

replacement cycle

Remarks/conditions

Fan motor

Approx. 50,000 hours

—

Power supply

Approx. 40,000 hours

—

Print head

After using approx.

1,000 rolls of

recording paper

—

LCD backlight

(Half-life of

brightness)

Approx. 80,000 hours At ambient temperature of 25°C

The service life varies greatly depending on the ambient environment.

The service life becomes shorter under high temperature in particular.

Model U8330 SSD

Unit

Approx. 20,000 hours

(continuous writing)

In ambient environment of 25°C TBW (Total Byte Written): Approx. 60

Data retention period: Approx. one year (When power is OFF)

It is recommended to back up the data at regular intervals.

Electrolytic

capacitors

Approx. 50,000 hours PCBs on which an electrolytic capacitor must be replaced.

19 Maintenance and Service

Maintenance and Service

Содержание MR8827




















































































































































































































































































































































































































































Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды

Hioki MR8827, Инструкция по эксплуатации

Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды