Hioki MR8827 Скачать руководство пользователя страница 194

Страница: 194 / 436

189

Set the Trigger Mode

9.2 Set the Trigger Mode

This setting controls whether the instrument continues to accept triggers after measuring.

If all trigger sources are disabled (Off, with no trigger setting), measurement starts immediately (free-

running).

Procedure

Press the

DISP

key to open the Waveform screen.

Move the cursor to

[Trigger].

Select the trigger mode.

Single

Only one trigger is recognized. After pressing the

START

key, once a trigger is applied, a waveform is recorded for the

specified recording length, then measurement stops.

Repeat

Triggers are accepted continuously.

When no trigger is applied, the instrument enters the Trigger

Wait state. Press the

STOP

key to stop measurement. (See

below)

Auto

Triggers are accepted continuously.

If no trigger is applied within about one second, a waveform

of the specified recording length is automatically recorded.

Press the

STOP

key to stop measurement.

Available options depend on the function.

Trigger modes

Function

Single

(Default setting)

Repeat

Auto

(Default setting)

To Stop Measurement, press the

STOP

key.

Press once: Recording will stop at the end of the specified recording length.

Press twice: Recording stops when the key is pressed.

When the trigger mode is set to

[Repeat]

During the processing interval (auto-save, auto-print, waveform display processing, numerical calculation)

from the end of recording until next entering the Trigger Wait state, triggering will not be accepted.

Trigger Settings

Содержание MR8827




















































































































































































































































































































































































































































Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды

Hioki MR8827, Инструкция по эксплуатации

Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды