manualshive.com logo in svg

Hioki MR8827, Инструкция по эксплуатации

Инструкция к счетчику Hioki MR8827 доступна для скачивания бесплатно на manualshive.com. Руководство содержит все необходимые сведения для эффективного использования продукта. Скачайте руководство сейчас и получите полную информацию о функциях устройства.

Поделиться
Скачать
background image

11

Operation Precautions

Before Connecting a Logic Probe to the Measurement Object

DANGER

To avoid electric shock and short circuit accidents or damage to the instrument, 

confirm the following:

 

•

The ground pin in the LOGIC connector (plug) of Models 9320-01 and 9327 

Logic Probes is not isolated from the instrument’s ground (common ground). 

Use grounding-type polarized power cords for the measurement object and this 

instrument, and obtain power from the same mains circuit.

Connecting to different mains circuits or using a non-grounding power cord 

may cause damage to the measurement object or this instrument because 

of current flow through the logic probes resulting from potential difference 

between the grounds of the different wiring systems.

To avoid these problems, we recommend the following connection procedure:

Measurement

Object

Measurement

Object

GND

Logic probe

Logic probe

Functional Earth 

Terminals

Memory

HiCorder

Memory

HiCorder

Connect this instrument to the 

same outlet as the measurement 

object using the (supplied) 

grounding polarized power cord.

Connect the measurement object’s 

ground to the GND terminal 

(functional earth terminal) of this 

instrument.

(Always obtain power from the 

same mains circuit.)

See “2.5.2 Ground the Functional 

Earth of This Instrument” (page 

44)

Before Turning the Power Supply On

WARNING

 

•

To avoid electrical accidents and to maintain the safety specifications of this 

instrument, only connect the provided power cord to an outlet.

 

•

Before turning the instrument on, make sure the supply voltage matches that 

indicated on its power connector. Connection to an improper supply voltage 

may damage the instrument and present an electrical hazard.

CAUTION

Avoid using an uninterruptible power supply (UPS), DC/AC inverter with rectangular 

wave or pseudo-sine-wave output to power the instrument. Doing so may damage the 

instrument.
To avoid damaging the power cord, grasp the plug, not the cord, when unplugging it 

from the power outlet.

Turn off the power before connecting or disconnecting the power cord.

10

9

8

7

6

5

4

3

2

1

Appx.

Index

Содержание MR8827





















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MR8827

Parker 6513 Technical Manual preview
6513
Бренд: Parker Страницы: 54
Eclipse Combustion 6500 Instruction Manual preview
6500
Бренд: Eclipse Combustion Страницы: 46
Bard Duet Instructions For Use preview
Duet
Бренд: Bard Страницы: 2
parr 1108 Operating Instructions Manual preview
1108
Бренд: parr Страницы: 20
Landoll 2110 Operator'S Manual preview
2110
Бренд: Landoll Страницы: 71
York Fitness 2110 Owner'S Manual preview
2110
Бренд: York Fitness Страницы: 4
W&H 206 Operator'S Manual preview
206
Бренд: W&H Страницы: 23
Bartscher 105 Original Instruction Manual preview
105
Бренд: Bartscher Страницы: 24
dbx 911 Instruction Manual preview
911
Бренд: dbx Страницы: 12
dbx QUANTUM Application Manual preview
QUANTUM
Бренд: dbx Страницы: 13
dbx 1066 Operation Manual preview
1066
Бренд: dbx Страницы: 72
dbx AFS224 Quick Start Manual preview
AFS224
Бренд: dbx Страницы: 11
dbx 566 Owner'S Manual preview
566
Бренд: dbx Страницы: 16
Garmin PORTABLE ICE FISHING KIT Installation Instructions preview
PORTABLE ICE FISHING KIT
Бренд: Garmin Страницы: 5
Gaspardo SP SPRINT Manual preview
SP SPRINT
Бренд: Gaspardo Страницы: 16
Gastrodomus PH100 Installation, Operating And Service Instructions preview
PH100
Бренд: Gastrodomus Страницы: 4
HANYOUNG NUX HL Series Instruction Manual preview
HL Series
Бренд: HANYOUNG NUX Страницы: 2
Gastrodomus CL Instructions For Use And Maintenance Manual preview
CL
Бренд: Gastrodomus Страницы: 39

Бренды по названию

Популярные бренды

Загрузить еще бренды