Hioki MR8827 Скачать руководство пользователя страница 152

Страница: 152 / 436

147

Display Waveforms During Recording (Roll Mode)

8.2 Display Waveforms During Recording (Roll

Mode)

This applies to the Memory function only.

You can display and print the waveform at the same time as the data is acquired (if auto-print is enabled). (p. 109)

• If measurement is carried out at low sampling rate using the Memory function, a long time will be

required until data for the entire recording length have been collected. Roll Mode is useful in these

cases.

• The new waveform scrolls automatically.

Procedure

Press the

STATUS

key to open the Status screen, and then select the

[Status]

sheet.

Move the cursor to

[Roll Mode].

OFF

Normal recording. Data is displayed only after acquiring

the specified recording length.

Waveforms are displayed while recording (with 10 ms

and slower settings). When the timebase is set to 5 ms/

div or faster, waveforms are not displayed until after

acquisition has finished.

AUTO

Regardless of the timebase setting, whether or not

the waveform is displayed depends on the waveform

display magnification settings while the data is being

recorded. (Default setting)

However, when the waveform is displayed using a time

axis faster than 100 ms per division, or when the time

base is 5

s/div, the waveform will be displayed after it

has been captured.

When the Roll mode function is

[On]

•

Roll Mode function and Overlay function cannot be used together.

When the Roll Mode function is enabled, the Overlay function is automatically set to

[Off]

. And when the

Overlay function is enabled, Roll mode is set to

[Auto]

. (p. 148)

• The roll mode, memory division and waveform calculation functions cannot be used simultaneously.

Roll Mode Function

Memory Division

Function

Waveform Calculation

Function

Off

Note: When one function is set to

[On]

, the other functions are automatically set to

[Off]

• When auto-print (p. 109) is enabled, printing is available simultaneously with waveform display (if the

internal printer is installed). However, for X-Y waveforms, all data must be acquired before printing.

In addition, during evaluation by numerical calculation, automatic printing is carried out according to the

evaluation conditions when numerical calculation finishes.

When the Roll Mode function is

[Off]

Waveforms are displayed after the data has been acquired for the entire recording length, so with slow

sampling there may be a long wait after starting measurement before the waveform is displayed.

Utility Functions

Содержание MR8827




















































































































































































































































































































































































































































Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды

Hioki MR8827, Инструкция по эксплуатации

Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды