Hioki MR8827 Скачать руководство пользователя страница 11

Страница: 11 / 436

Operation Precautions

Operation Precautions

Before Use

Follow these precautions to ensure safe operation and to obtain the full benefits of the various

functions.

DANGER

If connection cables or instrument are damaged, there is a risk of electric shock.

Before using the instrument, perform the following inspection.

•

Before using the instrument, check that the insulation of the connection cables

is not damaged and that no metal parts are exposed. Using the instrument

under such conditions could result in electric shock. Replace the connection

cable with those specified by our company.

•

Verify that the instrument operates normally to ensure that no damage occurred

during storage or shipping. If you find any damage, contact your authorized

Hioki distributor or reseller.

Instrument Installation

WARNING

To avoid accidents or damage to the instrument, do not install the instrument in

locations that are:

•

Exposed to direct sunlight or high temperature

•

Exposed to corrosive or combustible gases

•

Exposed to a strong electromagnetic field or electrostatic charge

•

Near induction heating systems (such as high-frequency induction heating

systems and IH cooking equipment)

•

Susceptible to vibration

•

Exposed to water, oil, chemicals, or solvents

•

Exposed to high humidity or condensation

•

Exposed to high quantities of dust particles

CAUTION

Do not place the instrument in a location that is unstable or inclined. Do not place the

unit on another unit. Knocking-over or dropping the instrument can cause injury or

damage to the instrument.

Installation

Be sure to keep the specified clearances around the instrument to prevent overheating.

• Do not install the instrument with any side except the bottom facing down.

• Do not obstruct vents.

• Do not install the instrument at an angle.

At least 5 cm

At least 5 cm on all sides

Right side

Vents

Left side

Vents

At least 5 cm

At least 5 cm on all sides

Содержание MR8827




















































































































































































































































































































































































































































Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды

Hioki MR8827, Инструкция по эксплуатации

Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды