Hioki MR8827 Скачать руководство пользователя страница 158

Страница: 158 / 436

153

Convert Input Values (Scaling Function)

To reset scaling settings

Move the cursor to

[Setting]

, and select

[Reset]

To copy the scaling setting to another channel

The Channel screen -

[Scaling]

sheet can be used to copy a setting.

Refer to “8.9 Copy Settings to Other Channels (Copy Function)” (p. 163)

To use a combination of the Scaling and Variable functions (p. 158)

The full span of output from a sensor can be displayed. (p. 160)

At factory shipping, automatic correction of the variable function (p. 307) is set to

[On]

At this time, the Variable setting is altered so that it is linked to (dependent upon) the vertical axis (voltage

axis) range and scaling settings.

If you want the Variable function setting to take priority, use either of the following procedures:

•

Set Scaling first, then set the Variable function

• Set a Variable value before Scaling, then set Scaling.

When automatic correction of the Variable function (variable auto-adjustment) is disabled

[Off]

, the

Scaling and Variable settings are unlinked (independent of one another).

8.5.1

Scaling Examples

When using the clamp sensor

Example 1

Measure with the 10 A range of the Model 9018-50 Clamp on Probe and display the

measured data in units of [A] (Amperes)

The 9018-50 Clamp on Probe provides 0.2 V output when measuring 10 A. So Scaling should be

set to display 10 A with 0.2 V input (and 0 A with 0 V input).

Setting

Selection

Set

NUM or SCI

Clamp

9018-50

Unit*

Method*

Ratio

Ratio*

50.000

*: Set automatically when clamp sensor is selected.

Utility Functions

Содержание MR8827




















































































































































































































































































































































































































































Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды

Hioki MR8827, Инструкция по эксплуатации

Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды