Hioki MR8827 Скачать руководство пользователя страница 205

Страница: 205 / 436

200

Apply an External Trigger (External Trigger)

9.6 Apply an External Trigger (External Trigger)

An external signal applied to the External Control terminal can serve as a trigger source.

It can also be used to drive synchronized parallel triggering of multiple instruments.

Procedure

Press the

DISP

key to open the Waveform screen, and then press the

TRIG.SET

key to open the trigger settings

window.

Enable external triggering.
Move the cursor to

[Ext Trig].

Off

External triggering disabled.

(Default setting)

External triggering enabled.

Apply the input signal to the external trigger (EXT.TRIG)

terminal.

Refer to “17.2.5 External Trigger Terminal (EXT.TRIG)” (p. 344).

9.7 Trigger Manually (Manual Trigger)

Triggers can be applied manually by pressing the

Manual Trigger

key.

Manual triggering takes priority over all other trigger sources, regardless of

settings.

To stop recording,

press the

STOP

key.

Press the

key once

Recording is carried out for one recording length and

then stops.

Press the

key twice

Recording stops when the key is pressed.

As for other trigger types, triggering does not occur during pre-trigger standby. Set the trigger priority

function to

[On]

Refer to “9.8.2 Set Trigger Acceptance (Trigger Priority)” (p. 203).

Содержание MR8827




















































































































































































































































































































































































































































Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды

Hioki MR8827, Инструкция по эксплуатации

Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды